Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table
$8,629.99

The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch

Powermatic Pneumatic Dovetail Machine

Powermatic Pneumatic Dovetail Machine
$6,389.99

The POWERMATIC DT65 Single Spindle Dovetailer gives quality to the most popular joints of drawer construction. It provides an affordable way to produce cleanly cut, professional dovetails that will enhance your products. The DT65 is complete with 1HP 230V 1 phase motor, pneumatic clamping, magnetic starter, carbide tipped cutter, and a four-sided template that produces dovetails on 1", 1-1/2", 2", and 2-1/2" centerlines. The use of different dovetail centerlines gives a unique custom appearance.Four centerlines - 1", 1-1/2", 2" and 2-1/2" - create a custom appearance Pneumatic clamping provides quick locking and unlocking of the work piece Eccentric spindle collet for resharpened cutters Spring loaded carriage makes for smooth, effortless dovetail cutting Cutter height of 3/16" to 3/4" accommodates different cutting depths and board thicknesses Extra large soft grip handle provides positive control and comfort The precision linear carriage bearings are sealed on both ends to eliminate dust buildup Visual stylus and template aid in guiding the carriage Material stops provide convenient positioning of the workpiece Cast iron and steel construction for added stability and durability 1HP motor transfers plenty of power via the drive belt to the spindle Magnetic starter for safety Standard Equipment:Four-sided templateWorkstops Tool kit Dovetail bit Dust chute with hose

Powermatic Manual Dovetail Machine

Powermatic Manual Dovetail Machine
$3,912.00

The POWERMATIC DT45 manual dovetail machine is used to cut dovetails for drawers and various furniture components. The machine is equipped with a router spindle which allows cutting dovetails of adjustable height. The DT45 can machine four types of dovetails with different pitches. Locking and unlocking of pieces takes place manually by an eccentric clamp.Four centerlines - 1", 1-1/2", 2" and 2-1/2" - create a custom appearanceManual eccentric clamping will keep boards firm Eccentric spindle collet for resharpened cutters Spring loaded carriage makes for smooth, effortless dovetail cutting Cutter height of 3/16" to 3/4" accommodates different cutting depths and board thicknesses Extra large soft grip handle provides positive control and comfort The precision linear carriage bearings are sealed on both ends to eliminate dust buildup Visual stylus and template aid in guiding the carriage Material stops provide convenient positioning of the workpiece Cast iron and steel construction for added stability and durability 1HP motor transfers plenty of power via the drive belt to the spindle Product Specifications:Powermatic Part Number: 1791304Model Number: DT45Brand: PowermaticMotor Power: 1 HPMotor Phase: 1 PhMotor Voltage: 115 VPrewired Voltage: 115 VMinimum Work Piece: 7-7/8" x 2-3/8"Size (L x W): Maximum Work Piece: 31" x 11"Size (L x W): Minimum Dovetail Height: 3"Maximum Dovetail Height: 3"Minimum Front Thickness: 1"Maximum Front Thickness: 9"Minimum Side Thickness: 1"Maximum Side Thickness: 9"Number of Spindles: 1Spindle Speed: 18500 RPMCenter to Center: 1", 1-1/2", 2"Dovetail Spacing: and 2-1/2"Table Height from Floor: 35"Dust Port Outside Diameter: 2-1/2", 4" rearDust Collection Minimum: 500 cu.ft/minCFM Required: Height: 61"Width: 33"Length: 33"Net Weight: 320 lbsStandard Equipment:Four-sided template Workstops Tool kit Dovetail bit Dust chute with hose

CNC Shark Routing System

CNC Shark Routing System
$2,899.99

With a table measuring 15-3/4" x 31-1/2", the CNC Shark is ideally suited for carvings and machining operations on a large variety of signs, doors and other small projects. It boasts impressive power, speed, accuracy, and ease of use. With its robust steel and high-density poly-ethylene construction, it can take accidental impacts that would normally damage or destroy an aluminum or MDF machine. The included clamping table features two hold-down slots for securing work anywhere along the length of the table. You supply a PC computer with USB 2.0 port and a Bosch Colt router (sold separately). Simply connect the USB cable to the controller box and the other end to your computer (not compatible with Mac computers). The CNC Shark also includes the NEW Virtual Zero software. This new and CNC Shark exclusive software ''maps'' the surface of your table or work piece and uses the map as a dynamic reference point. This virtually eliminates problems caused by warped or bowed work pieces.FREE CNC Project Plans from Woodworker's Journal:Butler's TrayWeather StationCribbage BoardWorkshop JigModern TableOutlet CoverLuggage TagsChinese CheckerboardPuzzle TrayIntroducing CNCSharkTalk.com, a website presented by Rockler where CNC Shark users can chat together, watch how-to videos, ask questions, learn from each other and even show off their CNC Shark projects.

Sjobergs Elite Workbench 2500 with Cabinet SM04

Sjobergs Elite Workbench 2500 with Cabinet SM04
$2,730.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Sjobergs Elite Workbench 2000 with Cabinet SM04

Sjobergs Elite Workbench 2000 with Cabinet SM04
$2,575.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Jet FS-1652H Foot Shear, 52'' x 16 Gauge

Jet FS-1652H Foot Shear, 52'' x 16 Gauge
$2,399.00

Sometimes called ''stomp'' shears for the way they're operated, foot shears let you put the ''pedal to the metal'' to cut and dimension sheet steel of up to 16 gauge. The Jet FS-1652H Foot Shear features high quality, hardened and tempered stainless steel blades that are reversible for double the cutting life. Compound leverage allows the user to perform work within the machine's rated capacity with ease. An adjustable hold down clamp keeps materials secure during operation to prevent errors, while back and front gauges allow precise, repeatable cuts.Features:Ideal for precision shearing of mild steel up to 16 gaugeDual-sided blades provide twice the cutting lifeUpper blade is two-way; bottom blade is one-way2° angle cutting edge; 1° face relief

Sjobergs Elite Workbench 1500 with Cabinet SM03

Sjobergs Elite Workbench 1500 with Cabinet SM03
$2,265.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Sjobergs Elite Workbench 2500

Sjobergs Elite Workbench 2500
$2,215.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Sjobergs Elite Workbench 2000

Sjobergs Elite Workbench 2000
$2,060.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Sjobergs Elite Workbench 1500

Sjobergs Elite Workbench 1500
$2,000.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

CNC Piranha

CNC Piranha
$1,599.99

Although its attractive price might suggest an entry level machine, the CNC Piranha is every bit as capable as its CNC Shark cousins and it even includes a convenient touch-screen interface! Its compact 12'' x 18'' table makes it perfect for smaller-scale projects like carvings, plaques, ornamental boxes and precision parts machined from wood, soft metals, or plastics, all at a fraction of the price of a full-sized CNC. With its 3D carving capability, including a 3D models library, you can carve expensive corbels, cut intricate inlays and engravings. The CNC Piranha has such incredible accuracy that you can engrave custom circuit boards with it. In addition, the entire machine can easily fit on one end of your bench. Design your project with the included VCarve Desktop 8.0 Design software on a PC computer with USB 2.0 port (computer not included). Then save the program directly to a USB flash drive, plug it into the Pendant, select your file, and hit the run button. By using the flash drive, your computer won't be subjected to a dusty shop environment. Put the power of the Piranha to work for you today! Made in USA.Note:Requires a PC computer with USB 2.0 port (not included)Requires a Bosch, Dewalt, Porter Cable, or similar style palm router (sold separately). Included router clamp fits the Bosch router; Dewalt and Porter Cable routers require a separate router clamp (58703, sold separately)Currently not compatible with the Touch Probe (upgrade coming soon)

Sjobergs Scandi Plus Workbench 1825 with SM03 Cabinet

Sjobergs Scandi Plus Workbench 1825 with SM03 Cabinet
$1,595.00

With versatility and durability in spades, the Sjobergs Scandi Plus workbenches are perfectly suited for the demanding work of professional woodworkers and serious craftsmen. For strength, the tops are constructed with full-length laminations of knot-free European beech, without any ugly splices. With a thickness of 1-1/2'' in the center, and a skirt of 4-5/16'', the top is extremely strong. Solid beech is also used in the preassembled trestle frames. The bench has two double rows of 3/4'' dog holes working from both the front and tail vises, as well as dog holes in the trestle legs for a wide variety of clamping options. Includes four unbreakable bench dogs with side springs to ensure that they stay at the desired height. The dogs automatically adjust to non-parallel workpieces. Made in Sweden, Sjobergs Scandi Plus workbenches are built to provide a lifetime of hard use and enjoyment. Tops are extremely strong—1-1/2'' thick in the middle, and 4-1/4'' around the edgeVises have a 4-1/2'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four 3/4'' round plastic/glass fiber bench dogs

Sjobergs Scandi Plus Workbench 1425 with SM03 Cabinet

Sjobergs Scandi Plus Workbench 1425 with SM03 Cabinet
$1,442.00

With versatility and durability in spades, the Sjobergs Scandi Plus workbenches are perfectly suited for the demanding work of professional woodworkers and serious craftsmen. For strength, the tops are constructed with full-length laminations of knot-free European beech, without any ugly splices. With a thickness of 1-1/2'' in the center, and a skirt of 4-5/16'', the top is extremely strong. Solid beech is also used in the preassembled trestle frames. The bench has two double rows of 3/4'' dog holes working from both the front and tail vises, as well as dog holes in the trestle legs for a wide variety of clamping options. Includes four unbreakable bench dogs with side springs to ensure that they stay at the desired height. The dogs automatically adjust to non-parallel workpieces. Made in Sweden, Sjobergs Scandi Plus workbenches are built to provide a lifetime of hard use and enjoyment. Tops are extremely strong—1-1/2'' thick in the middle, and 4-1/4'' around the edgeVises have a 4-1/2'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four 3/4'' round plastic/glass fiber bench dogs

SawStop 10'' Jobsite Saw

SawStop 10'' Jobsite Saw
$1,299.00

The SawStop Jobsite Saw packs all of the safety of SawStop's revolutionary blade brake, plus a raft of other innovative features, into a compact, portable table saw. Whether on the jobsite or at home, you can rest easy with the safety and peace of mind of a SawStop saw. Landing somewhere between a benchtop saw and a contractor's saw in terms of size, the SawStop Jobsite Saw offers numerous benefits of both. It includes a pedal-actuated folding stand-one press and it unfolds from a compact vertical storage position to cutting mode. In transport mode, the stand acts as a dolly with 8'' wheels that allow you to easily move it over rough terrain and up ramps and stairs. The cleverly-designed table extension rides on rails that slide out for a maximum rip cut of 25-1/2'' right of the blade, while the smooth-sliding T-square fence ensures precise cuts and excellent parallelism with the blade. Of course, and perhaps best of all, the SawStop safety brake will stop the blade immediately on contact with skin, a particularly important feature on the jobsite where less than ideal working conditions can lead to increased risk of accidents. SawStop Safety Brake: Brings the blade to a halt almost instantly on contact with skinOne-Turn Blade Elevation: Other saws require over 25 turns to raise or lower the blade-with the Jobsite Saw, it's accomplished with a single turn!Quick-Tilt Blade Angle: Tilt the blade quickly and easily to your desired angle in 1° incrementsMicro Adjust Blade Angle: Fine tune your tilt with the infinitely-adjustable micro adjustT-Style Fence with ErgoLock: Jobsite T-Glide Fence slides smoothly and locks firm with the innovative ErgoLock. T-style design minimizes deflection to increase accuracy. Extend the OnDemand Shelf for support when needed.Fence Storage Holster: Side brackets offer convenient storage for the fence and cordLow-Profile Blade Guard: The Micro Guard increases visibility and protects against kickback with less interference than other guards. Quickly switch between the Micro Guard and the provided riving knife with the flip of a leverPedal-Activated Folding Stand: Simply push the pedal to release and fold the cart for travelLarge Wheels: 8'' wheels are ideal for the varied terrain of most jobsitesControl Box: Features the largest Start/Stop paddle in the category and lights to communicate system status. Use the control box to bypass the safety system to test for and/or cut conductive materialsTool-Free Zero-Clearance Insert: Quickly releases with no need for tools.Accessory Storage Drawer: Keep your accessories-your micro guard, riving knife, miter gauge and more-protected and ready at hand with the onboard storage drawerTable Extension Clamp: Locks and unlocks easily, allowing you to quickly extend the table to a full 25-1/2'' rip capacity!

Powermatic Tilt Table Mortiser w/Stand

Powermatic Tilt Table Mortiser w/Stand
$1,274.99

The 719T Tilt Table Mortiser features heavy-duty cast iron construction and a powerful 1HP motor for the most demanding jobs. The head is mounted using adjustable gibs to assure years of trouble-free service. The heavy rack and pinion gear system utilizes a spring-loaded six position adjustable handle for movement. A handy depth stop gives a uniform depth of mortise. A large 20-1/4" x 7" table gives plenty of work support and will adjust to any angle between 0 and 35°. The table can also move left to right and forward and back on dovetail ways with the large handwheel controls. Adjustable linear stops and flip down stop allow for precision repeatability. The quick adjust clamp provides plenty of work-holding force and will swivel to accommodate angled workpieces. The heavy enclosed steel cabinet provides plenty of storage inside for chisels and accessories. Sturdy cast iron construction with precision-machined column and table Quick position table mounted swiveling vise clamp accommodates angled work pieces Feed lever features size positions allowing for quick adjustments Table and fence tilt from 0 to 35° for angled mortises Gas cylinder controlled rack and pinion system for smooth head raising and lowering Hinged chuck door allows easy access for quick bit changes Quick adjust depth stop for uniform mortise depths Provided 5/8", 3/4" and 1-1/8" bushings allow multiple chisel shank sizes Handwheels control smooth linear and cross table motions Adjustable work stop for repeat cuts Standard Equipment 1HP motor Work stop for repeat cut Depth and length stops Enclosed stand with shelf Gas spring assists head travel for smooth movement Quick-release vise for speedy release of work material 6 position feed lever

Sjobergs Duo Workbench with SM03 Cabinet

Sjobergs Duo Workbench with SM03 Cabinet
$1,175.00

With four standard vise locations—one on each end, and two along the front edge—the Sjobergs Duo is capable of securely holding nearly any workpiece. Constructed entirely from solid European beech, it also makes no sacrifices in durability. The vises can be rotated to suit left- or right-handed woodworkers. In addition, they can be positioned as dual front vises to hold extra-long boards for jointing, or as dual tail vises for an extended lengthwise clamping capacity of 63''. For strength, the tops are constructed with full-length laminations of knot-free European beech, without any ugly splices. With a thickness of just over 1'' in the center, and a skirt of 2-3/4'', the top is very rigid. The Sjobergs Duo cabinetmaker's workbench is built to provide a lifetime of hard use and enjoyment. Beech top is just over 1'' thick in the middle, and 2-3/4'' around the edgeVises have a 4-1/2'' opening capacityDouble rows of bench dog holes extend from all vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass for less vibrationIncludes four 3/4'' round plastic/glass fiber bench dogs

Sjobergs Scandi Plus Workbench 1825

Sjobergs Scandi Plus Workbench 1825
$1,133.00

With versatility and durability in spades, the Sjobergs Scandi Plus workbenches are perfectly suited for the demanding work of professional woodworkers and serious craftsmen. For strength, the tops are constructed with full-length laminations of knot-free European beech, without any ugly splices. With a thickness of 1-1/2'' in the center, and a skirt of 4-5/16'', the top is extremely strong. Solid beech is also used in the preassembled trestle frames. The bench has two double rows of 3/4'' dog holes working from both the front and tail vises, as well as dog holes in the trestle legs for a wide variety of clamping options. Includes four unbreakable bench dogs with side springs to ensure that they stay at the desired height. The dogs automatically adjust to non-parallel workpieces. Made in Sweden, Sjobergs Scandi Plus workbenches are built to provide a lifetime of hard use and enjoyment. Tops are extremely strong—1-1/2'' thick in the middle, and 4-1/4'' around the edgeVises have a 4-1/2'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncludes four 3/4'' round plastic/glass fiber bench dogs

Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page