Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table
$8,629.99

The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch

Supermax 37'' Dual Drum 3 Phase Sander - 737103

Supermax 37'' Dual Drum 3 Phase Sander - 737103
$6,049.99

Make quick, easy work of large-scale production sanding and get remarkably smooth, consistent results with this SuperMax 37'' Dual Drum Sander. Equipped with a continuous-duty 5HP 208-230V three-phase motor, it can handle pieces up to 37" wide and 12" thick.Shown with SuperMax Caster Set - Sold Separately (1004534), SuperMax ProScale DRO - Sold Separately (1004533) and SuperMax Rack'N Roll - Not Included.Exceptional SuperMax FeaturesINTELLISAND Control: Automatically adjusts conveyor speed based on load Prevents gouging, damaging or burning stock Provides consistent finish even with varying grain pattern and density Greatly increases abrasive planing and dimensioning speedFlatness Guarantee: Precision-flattened steel conveyor bed reinforced with four steel cross sections for no "flex" in conveyor, guaranteeing flatness to less than .010" across the width of the sanderAbrasive conveyor belt offers the best grip for raw wood, giving you the ability to accommodate stock that is much shorter or thinnerPatented Abrasive Attachment System effectively tensions the abrasive wraps, preventing loose abrasive and overlapEasiest access to abrasive fastening system of any drum sander! Machine design includes additional space around abrasive, eliminating the need for special tools.Self-cooling drum prevents overheating and extends abrasive lifeAdditional Features Drum ball bearing are sealed and permanently lubricated Cast stand, zinc-plate steel bed, centerless ground column tubes

Supermax 37'' Dual Drum 3 Phase Sander - 737003

Supermax 37'' Dual Drum 3 Phase Sander - 737003
$6,049.99

Make quick, easy work of large-scale production sanding and get remarkably smooth, consistent results with this SuperMax 37'' Dual Drum Sander. Equipped with a continuous-duty 5HP 208-230V three-phase motor, it can handle pieces up to 37" wide and 12" thick.Shown with SuperMax Caster Set - Sold Separately (1004534), SuperMax ProScale DRO - Sold Separately (1004533) and SuperMax Rack'N Roll - Not Included.Exceptional SuperMax FeaturesINTELLISAND Control: Automatically adjusts conveyor speed based on load Prevents gouging, damaging or burning stock Provides consistent finish even with varying grain pattern and density Greatly increases abrasive planing and dimensioning speedFlatness Guarantee: Precision-flattened steel conveyor bed reinforced with four steel cross sections for no "flex" in conveyor, guaranteeing flatness to less than .010" across the width of the sanderAbrasive conveyor belt offers the best grip for raw wood, giving you the ability to accommodate stock that is much shorter or thinnerPatented Abrasive Attachment System effectively tensions the abrasive wraps, preventing loose abrasive and overlapEasiest access to abrasive fastening system of any drum sander! Machine design includes additional space around abrasive, eliminating the need for special tools.Self-cooling drum prevents overheating and extends abrasive lifeAdditional Features Drum ball bearing are sealed and permanently lubricated Cast stand, zinc-plate steel bed, centerless ground column tubes

Powermatic PM1800B 18'' Bandsaw, 5HP, 1-Phase, 230V

Powermatic PM1800B 18'' Bandsaw, 5HP, 1-Phase, 230V
$4,999.99

Designed with an enormous 18'' resaw capacity, multi-step blade tensioning system, precision blade guides, and a 5HP motor hungry for hardwoods, the new PM1800 is a bandsaw like no other. It comes standard with all the extra features you've come to expect from Powermatic. With its 24'' x 27'' cast iron table and precision balanced cast iron wheels, it runs smoothly and quietly, with hardly any vibration. The easy-to-adjust T-square style fence includes a 6-1/2'' resaw fence that gives you excellent right angle support when running wide boards vertically. Whether you're resawing thin veneers or just thicknessing boards to minimize waste that would otherwise be eaten by your planer, this saw is more than up to the task. Read on to learn more about this industrial-quality bandsaw from Powermatic. Features:Blade tension lever has full tension, partial tension, and release settings for easy blade changes and trackingMicro-adjustable, virtually tool-free bearing guide system gives precise blade control with reduced frictionGrooved thrust bearing stabilizes smaller bladesMagnetic starter with power indicator lamp and jumbo stopMagnetic switch protects the motor from harm due to potential electrical supply issuesSolid chrome knobs and handles ensure solid grip and firm lockingComputer balanced cast iron wheels reduce vibrationAdjustable miter gauge with stopsExclusive Powermatic T-Square style Accu-Fence maximizes accuracy and safetyAccu-Fence has complete adjustability for aligning to blade and squaring to tablePositive locking cam with pressure adjustmentOversized side plate can be used in the horizontal or vertical positionElectrical interlock prevents the bandsaw from starting when the blade is de-tensioned (patent pending)Four-sided blade guard for optimum protectionIntegrated foot brake stops the coasting blade

Powermatic PM1800B-3 18'' Bandsaw, 5HP, 3-Phase, 230/460V

Powermatic PM1800B-3 18'' Bandsaw, 5HP, 3-Phase, 230/460V
$4,999.99

Designed with an enormous 18'' resaw capacity, multi-step blade tensioning system, precision blade guides, and a 5HP motor hungry for hardwoods, the new PM1800 is a bandsaw like no other. It comes standard with all the extra features you've come to expect from Powermatic. With its 24'' x 27'' cast iron table and precision balanced cast iron wheels, it runs smoothly and quietly, with hardly any vibration. The easy-to-adjust T-square style fence includes a 6-1/2'' resaw fence that gives you excellent right angle support when running wide boards vertically. Whether you're resawing thin veneers or just thicknessing boards to minimize waste that would otherwise be eaten by your planer, this saw is more than up to the task. Read on to learn more about this industrial-quality bandsaw from Powermatic.Features:Blade tension lever has full tension, partial tension, and release settings for easy blade changes and trackingMicro-adjustable, virtually tool-free bearing guide system gives precise blade control with reduced frictionGrooved thrust bearing stabilizes smaller bladesMagnetic starter with power indicator lamp and jumbo stopMagnetic switch protects the motor from harm due to potential electrical supply issuesSolid chrome knobs and handles ensure solid grip and firm lockingComputer balanced cast iron wheels reduce vibrationAdjustable miter gauge with stopsExclusive Powermatic T-Square style Accu-Fence maximizes accuracy and safetyAccu-Fence has complete adjustability for aligning to blade and squaring to tableSturdy cast iron table and trunnion assembly offers maximum rigidity for large work piecesPositive locking cam with pressure adjustmentOversized side plate can be used in the horizontal or vertical positionElectrical interlock prevents the bandsaw from starting when the blade is de-tensioned (patent pending)Four-sided blade guard for optimum protectionIntegrated foot brake stops the coasting blade

Powermatic 18'' Bandsaw 5HP 3PH

Powermatic 18'' Bandsaw 5HP 3PH
$4,794.99

The new PM1800 Bandsaw is a part of the new breed of high performance products from Powermatic - the Gold Standard since 1921. Designed with an enormous 18" resaw, multi-step blade tension, precision blade guides, and a 5HP motor hungry for hardwoods, this powerhouse comes standard with all the extra features you've come to expect from Powermatic.Features:Tension lever has full tension, partial tension, and blade release settings for easy blade changes and trackingMicro-adjustable, virtually tool-less bearing guide system gives close blade control while reducing frictionSpecial grooved thrust bearing stabilizes smaller bladesHeavy duty T-style rip fence has adjustable aluminum resaw fenceLarge 24" x 24" cast iron table2-inch diameter solid steel pin for resaw workMagnetic starter with power indicator lamp and jumbo stopChrome knobs and handle ensure solid grip and firm locking of partsComputer balanced cast iron wheels reduce vibrationDual 4-inch exhaust ports for effective dust and chip removalAdjustable miter gauge with stops

Powermatic 18'' Bandsaw 5HP 1PH

Powermatic 18'' Bandsaw 5HP 1PH
$4,794.99

The new PM1800 Bandsaw is a part of the new breed of high performance products from Powermatic - the Gold Standard since 1921. Designed with an enormous 18" resaw, multi-step blade tension, precision blade guides, and a 5HP motor hungry for hardwoods, this powerhouse comes standard with all the extra features you've come to expect from Powermatic.Features:Blade tension lever has full tension, partial tension, and blade release settings for easy blade changes and trackingMicro-adjustable, tool-less bearing guide system gives close blade control while reducing frictionSpecial grooved thrust bearing stabilizes smaller bladesHeavy duty T-style rip fence has adjustable aluminum resaw fenceLarge 24" x 24" cast iron table2-inch diameter solid steel pin for resaw workMagnetic starter with power indicator lamp and jumbo stop Chrome knobs and handles ensure solid grip and firm locking of partsComputer balanced cast iron wheels reduce vibrationDual 4-inch exhaust ports for effective dust and chip removalAdjustable miter gauge with stops

Jet 20'' 3HP Bandsaw w/Quick Tension

Jet 20'' 3HP Bandsaw w/Quick Tension
$2,904.99

This 20-inch Bandsaw features a strong 3HP motor and poly v-belt drive for efficient power transfer. A three-position tensioner allows quick blade adjustments and tracking. The micro-adjustable ball bearing guides run smoothly with less friction heat. The extra large cast trunnion system and triangular-design frame dampen vibration and provide superior stability.Features:Triangular design provides superior column rigidity12-1/4" Resaw capacity for cutting large pieces of wood, slicing veneers and cutting book matched panels21" x 21" precision ground cast iron table for added stability and work support2 Speed poly V-belt drivePrecision computer balanced wheels eliminate vibration for accurate blade trackingFoot brake for rapid stopsUpper and lower ball bearing, micro-adjustable blade guides for proper support during the cut of different size boardsTool-less, independently adjustable ball bearing guide system for quick and easy adjustments and smooth operationRigid, heavy-duty guide post with rack and pinion adjustment for extra blade supportAll cast iron handwheels make smooth, easy blade adjustments with less effort1", 3 TPI woodworking blade is included so you can start cutting right awayExtra large cast trunnion for better support and stabilityDual locking cabinet doors allow access to blade when necessaryBlade tension scale allows precise blade tensioningSingle knob tracking adjustment simplifies the blade tracking processExclusive quick-release, precision T-square style rip fence with resaw post4" dust port allows for direct connection of dust collection system

Jet Deluxe Xacta 5HP 10'' Table Saw w/50'' Fence, Downdraft Table, & Leg Set

Jet Deluxe Xacta 5HP 10'' Table Saw w/50'' Fence, Downdraft Table, & Leg Set
$2,859.99

EXCLUSIVE Commercial XACTA Fence II with T-square design Quick release riving knife greatly reduces binding/kickback risk JET downdraft table with exclusive design (patent pending), draws harmful dust particles away from the user without obstructing the user's movement or productivity Push button arbor lock (patent pending) for rapid blade change Shrouded Blade increases dust collection efficiency Standard 11" left and right cast iron extension wings provides the largest table surface in its class Poly-V drive belt system delivers efficient, quiet operation Rail-mounted magnetic switch is easy to reach and provides overload protection Enclosed cabinet with built-in sealed storage drawer Hinged motor cover on cabinet gives quick access to the motor and belts Deluxe miter gauge with adjustable positive stops and large soft grip handles provides large crosscutting capacity and accurate miters Heavy-duty chrome plated handwheels contribute to smooth trunnion/arbor movement Left tilt, wide stance heavy-duty trunnion for stability and smooth blade positioning 5 Year Warranty

Sjobergs Elite Workbench 2500 with Cabinet SM04

Sjobergs Elite Workbench 2500 with Cabinet SM04
$2,730.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Supermax 25'' Dual Drum 1 Phase Sander - 713003

Supermax 25'' Dual Drum 1 Phase Sander - 713003
$2,690.00

Make quick, easy work of large-scale production sanding and get remarkably smooth, consistent results with this SuperMax 25'' Dual Drum Sander. Equipped with a continuous-duty 5HP 208-230V single-phase motor, it can handle pieces up to 25'' wide and 6'' thick. (Shown with SuperMax Caster Set, Sold Separately 1004534)Exceptional SuperMax FeaturesINTELLISAND Control: Automatically adjusts conveyor speed based on load Prevents gouging, damaging or burning stock Provides consistent finish even with varying grain pattern and density Greatly increases abrasive planing and dimensioning speedFlatness Guarantee: Precision-flattened steel conveyor bed reinforced with four steel cross sections for no "flex" in conveyor, guaranteeing flatness to less than .010" across the width of the sanderAbrasive conveyor belt offers the best grip for raw wood, giving you the ability to accommodate stock that is much shorter or thinnerPatented Abrasive Attachment System effectively tensions the abrasive wraps, preventing loose abrasive and overlapEasiest access to abrasive fastening system of any drum sander! Machine design includes additional space around abrasive, eliminating the need for special tools.Self-cooling drum prevents overheating and extends abrasive lifeAdditional Features Drum ball bearing are sealed and permanently lubricated Cast stand, zinc-plate steel bed, centerless ground column tubes

Supermax 25'' Dual Drum 3 Phase Sander - 713103

Supermax 25'' Dual Drum 3 Phase Sander - 713103
$2,690.00

Make quick, easy work of large-scale production sanding and get remarkably smooth, consistent results with this SuperMax 25'' Dual Drum Sander. Equipped with a continuous-duty 5HP 208-230V three-phase motor, it can handle pieces up to 25'' wide and 6'' thick.(Shown with SuperMax Caster Set, Sold Separately 1004534)Exceptional SuperMax FeaturesINTELLISAND Control: Automatically adjusts conveyor speed based on load Prevents gouging, damaging or burning stock Provides consistent finish even with varying grain pattern and density Greatly increases abrasive planing and dimensioning speedFlatness Guarantee: Precision-flattened steel conveyor bed reinforced with four steel cross sections for no "flex" in conveyor, guaranteeing flatness to less than .010" across the width of the sanderAbrasive conveyor belt offers the best grip for raw wood, giving you the ability to accommodate stock that is much shorter or thinnerPatented Abrasive Attachment System effectively tensions the abrasive wraps, preventing loose abrasive and overlapEasiest access to abrasive fastening system of any drum sander! Machine design includes additional space around abrasive, eliminating the need for special tools.Self-cooling drum prevents overheating and extends abrasive lifeAdditional Features Drum ball bearing are sealed and permanently lubricated Cast stand, zinc-plate steel bed, centerless ground column tubes

Jet Deluxe Xacta 3HP 10'' Table Saw w/50'' Fence, Downdraft Table, & Leg Set

Jet Deluxe Xacta 3HP 10'' Table Saw w/50'' Fence, Downdraft Table, & Leg Set
$2,649.99

EXCLUSIVE commercial XACTA Fence II with T-square design JET downdraft table with exclusive design (patent pending), draws harmful dust particles away from the user without obstructing the user's movement or productivity Quick release riving knife greatly reduces binding/kickback risk Push button arbor lock (patent pending) for rapid blade change Shrouded Blade increases dust collection efficiency Standard 11" left and right cast iron extension wings provides the largest table surface in its class Poly-V drive belt system delivers efficient, quiet operation Rail-mounted magnetic switch is easy to reach and provides overload protection Enclosed cabinet with built-in sealed storage drawer Hinged motor cover on cabinet gives quick access to the motor and belts Deluxe miter gauge with adjustable positive stops and large soft grip handles provides large crosscutting capacity and accurate miters Heavy-duty chrome plated handwheels contribute to smooth trunnion/arbor movement Left tilt, wide stance heavy-duty trunnion for stability and smooth blade positioning 5 Year Warranty

Jet Drum Sander 3HP With Table & Casters

Jet Drum Sander 3HP With Table & Casters
$2,649.99

The new JET model 22-44 PRO-3 - Drum Sander has even more great features. We've added a digital readout that displays the exact thickness of the finished piece or allows the user to preset the exact thickness they want for the finished piece. Four casters mobilize your drum sander and also lock into place for stability during use. Both infeed and outfeed tables come standard with the 22- 44 PRO-3 and provide extra support for the workpiece. The powerful 3HP motor is designed for heavier use for longer periods of time.Features:Our Exclusive SandSmart Infinitely variable-feed control produces the ultimate finish at a rate from 0 to 10 feet per minute and prevents machine overloadPatented conveyor belt TRACKERS dramatically reduce the need for manual belt adjustments22'' wide suspended drum is supported on both ends with a truss-like carriage arm for greater strength and easy alignment to the table surface for consistent performanceSealed and permanently lubricated drum ball bearings for longer lifePrecision-flattened reinforced steel conveyor bed and no-give power feed belt provide a constant smooth sanding action for better resultsAdjustable drum height and downward pressure feature virtually eliminates snipeLarge cast-iron handwheel adjusts height at 3/32'' per turn for precise sanding thickness controlPatented abrasive take-up fasteners make changing abrasives quick and easyDepth gauge has locking stop to ensure accuracyOn/off switch with overload protection is front- mounted for operator's convenienceOne feed and one drive motor for superior sanding controlContinuous-duty, 3HP motor is designed for heavier use for longer periods of timeDRO for more accurate sanding

Sjobergs Elite Workbench 2000 with Cabinet SM04

Sjobergs Elite Workbench 2000 with Cabinet SM04
$2,575.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Jet Oscillating Drum Sander 1.75HP w/Closed Stand

Jet Oscillating Drum Sander 1.75HP w/Closed Stand
$2,449.99

The new model 22-44 OSC Drum Sander has an exclusive oscillating feature, with the push of a button the 22-44OSC sander can be operated as a simple sander or as an oscillating sander. When operating as a linear sander, the sander drum rotates as the conveyor feeds the workpiece through. When in the oscillating mode, in addition to the linear sanding operation, the sanding drum head oscillates from left to right and lowers heat build-up on the sanding belt to reduce loading and burning. Additional features include a built-in cabinet door for easy access to storage, patented conveyor TRACKERS that reduce the need for manual belt adjustments and our Exclusive SandSmart infinitely variable feed control that produces the ultimate finish to your woodworking project.Features:Oscillating feature reduces heat build-up on sanding belt to reduce loading and burning Infinitely variable-feed control produces the ultimate finish at a rate from 0 to 10 feet per minute Patented conveyor belt TRACKERS dramatically reduce the need for manual belt adjustments Sealed and permanently lubricated drum ball bearings for longer life Precision-flattened reinforced steel conveyor bed and no-give power feed belt provide a constant smooth sanding action for better results Adjustable drum height and downward pressure feature virtually eliminates snipe Large cast-iron handwheel adjusts height at 3/32" per turn for precise sanding thickness control Patented abrasive take-up fasteners make changing abrasives quick and easy Depth gauge has locking stop to ensure accuracy On/off switch with overload protection is front-mounted for operator's convenience One feed and one drive motor for superior sanding control Continuous-duty, 1-3/4HP motor is designed for heavier use for longer periods of time Our EXCLUSIVE SandSmart infinitely variable-feed control produces the ultimate finish at a rate from 0 to 10 feet per minute and prevents machine overload

Jet JMD-18 Mill/Drill with R-8 Taper, 115/230V, Single-Phase

Jet JMD-18 Mill/Drill with R-8 Taper, 115/230V, Single-Phase
$2,299.00

The Jet JMD-18 is a lighter, space-saving alternative to a dedicated milling machine. It combines a belt driven drill press with the dual coordinate abilities of the milling machine's moveable table, providing three microadjustable axes for precision results in a variety of metal machining projects. Although light in construction, the JMD-18 milling/drilling machine possesses the advantages of space-saving versatility and affordability with good light machining capability. It features a one-piece cast iron column for rigidity, large hand wheels, a spacious worktable, and a highly versatile 360° swiveling head. The heavy-duty tapered roller bearings provide solid support to the spindle for finer tolerances and more accurate results.Features:One-piece cast iron column for added supportNew positive quick-stop knob and easy-to-read internal depth gauge (external on JMD-15)Belt cover with quick slide latch allows faster belt adjustment to change spindle speedsLocking collet prevents cutting tool from falling away from the spindle when lateral forces are exerted on the bitHeavy-duty tapered roller bearings support the spindle, resulting in greater tolerance and more accurate drilling depthBase taper allows for easier clean upLarger hand wheel knobsDrill press angle viseUL Listed motorExtra large worktable360° head swivelWork lampHeavy-duty power downfeed with manual fine feed1/2'' drill chuck, chuck arborDraw barDrill chuck guardAdjustable carbide facemillHeavy-duty stand is available separately (44415)

Sjobergs Elite Workbench 1500 with Cabinet SM03

Sjobergs Elite Workbench 1500 with Cabinet SM03
$2,265.00

The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers

Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page