Pages: first pageprev page1 2 3 4 5 6 7 8 9 10next pagelast page

16'' Longworth Style Chuck

16'' Longworth Style Chuck
$199.99

Just rotate the plates of the Longworth Style Chuck and the soft silicone buttons close in almost instantly, and with perfect concentricity, to hold your project while you make the finishing cuts to the bottom side. Unlike many other rechucking methods, the silicone buttons won't mar your project or your finish. When compressed with the wing nuts, they expand to provide a secure grip. The 1/4" thick phenolic plates provide strength and stability, regardless of humidity. Available in two sizes: the 10" Longworth Style Chuck for mini and midi lathes with a 10" swing, and the 16" Longworth Style Chuck for standard-sized lathes with a 16" swing or larger. Pick up a piece of fine china, and the first thing you'll do after admiring the faceis turn it over to inspect the bottom and insignia. It's no different with turnedbowls, and turners work hard to make the bottom as beautiful as the top. Butchucking a finished bowl face down on the lathe without damaging it hasalways been a challenge - not with the Longworth Style Chuck. Simply rotatethe plates, tighten down the buttons, and you're ready to turn.Eliminates the time and inconvenience of installing, adjusting and readjustingordinary rechucking jaws.Capable of holding projects in compression or expansion mode (from theinside or outside of the rim of your turning project).Buttons close in concentrically, making it easy to center your project.Soft silicone buttons have increased length for better grip and expansioncapabilities.Buttons expand when the wing nut is tightened, and will not mark or deformyour turned piece.Includes 8 buttons. Replacement packs of buttons with hardware are availableseparately (47455).No assembly required.1/4" phenolic discs are extremely durable, stable, and spin in opposingdirections with almost no resistance.The back side of the Longworth Style Chuck has a steel disk approximately 3/8"thick for mounting.The disk is easily gripped by any brand of 4-jaw scroll chuck with the standard50mm #2 jaws.Straight jaws may be used, but dovetail jaws provide a better hold.The dovetail groove accommodates Nova chucks and Vicmarc chucks as well asOneWay type straight jaws.Recommended maximum RPM is 600.Intended for light finishing cuts only. Note for heavy stock removal. Note: Best practice for safety dictates that you engage the tailstock wheneverpossible. Remove the tailstock only when finishing the last bit in the very center,and for finish sanding.Specifications:Capacity in compression mode: 4-1/2" to 14" in diameter.Capacity in expansion mode: 5-3/4" to 15-1/2" in diameter.

Work Sharp WS3000 Tool Sharpener

Work Sharp WS3000 Tool Sharpener
$199.99

Air-cooled, dry sharpening system eliminates the mess of a wet system and delivers higher material removal rates without affecting the steel temper. Unique design allows for fast and easy reshaping of new or damaged chisels and planes (up to 2" wide), and fast honing of a micro bevel. Bevel angles are adjustable and are set in the sharpening port (not in a fixture or jig) so switching between angles is simple and fast. With maintenance-free tempered glass grinding wheel. No calibration is required for changing wheel diameter, and there's no need to change between fixtures, grade wheels, or move from machine to hand sharpening to achieve a razor-sharp edge. Coarse grinding for rapid shaping and micro-fine honing is in one port!The system's repeatability allows you to sharpen multiple tools at any combination of angles and abrasive type without extra setup.Routed airflow and heat sink system keeps tools cool without the mess of a wet system.Sharpening port enables you to select desired bevel angle and sharpen precise, repeatable angles of 20&deg, 25&deg, 30&deg and 35&deg for chisels and plane irons up to 2" wide. Powerful 1/5 HP motor with 580 RPM wheel speed.Sharpening port lapping surface features "plunge-pull" sharpening technique.Sharpening port abrasive increases burr removal and speeds sharpening.Adjustable top tool rest makes freehand sharpening easier and more precise.T-slot mounting system lets you mount the top tool rest and other accessories.150mm tempered glass grinding wheel provides a maintenance-free, always flat and true grinding surface on which to adhere PSA abrasives.Skew cam adjustment controls bevel-edge for squareness.With bench mounting tabs for easy installation to benchtop.Industrial grade power connection switch with safety lockout.Grounded 6-foot power cord.Cast-aluminum top; sheet metal housing; impact and vibration-resistant tool-grade plastic base.The Work Sharp WS3000 Includes:Work Sharp unit Two tempered glass wheels See-through slotted wheel for underside sharpening of carving and lathe tools Top tool rest for easy freehand sharpening of larger tools Crepe stick for cleaning abrasives PSA abrasive kit (150mm to be adhered to glass wheels: P120 ceramic oxide, P400 aluminum oxide, P1000 aluminum oxide, Micro-Mesh 3600 honing abrasive; slotted abrasive kit with P80, P400 and P1200); and 2" x 2" abrasive P400 ceramic oxide for the heat sink/lapping surface.

Jet JWL-1221VS Bed Extension (719201)

Jet JWL-1221VS Bed Extension (719201)
$198.99

Extend the turning capacity of the JET 1221VS 12" x 21" Variable Speed Wood Lathe (45937, sold separately) to 43" for larger projects.

Oneway Scroll Chuck System

Oneway Scroll Chuck System
$195.29

2 levers plus 4 holes in body, 3 in the scroll gives you 1-handed tightening!ONEWAY chucks have been designed by a machinist with engineering input from material, heat treating, and plating specialists in order to satisfy the woodturner's every need. Chucks were designed to meet most turning needs. Less time spent getting ready to turn and more time spent turning means better quality, and more finished projects. Large projects can be turned more safely, and turning can be done at the ends of long stock.There are four lever holes in the body, and three holes in the scroll. This design creates a constant differential which allows one-handed tightening. Levers are made from high strength steel and will not deform or bend in use. This prevents damage to holes in the chuck.Different jaw sets are available for the chuck, which allows you to fit the chuck to suit your specific needs. If your needs change or grow, these chucks can be adapted to change and grow as you do.This chuck does require an insert, you can use: 3/4" x 16 tpi Insert (#22733 Sold Separately)or 1" x 8 tpi Insert (#22726 Sold Separately) or1-1/4'' x 8 tpi Insert (#21358 Sold Separately)The chuck weighs approximately 4.5 lbs.Standard Jaws & Optional Jaw Capacities are:#2 Jaws (Included) External 1-5/8" Min, 3" Max Internal 2" Min, 3-5/8" Max

Nova Swing-Away Lathe Attachment

Nova Swing-Away Lathe Attachment
$190.99

Get easy, unobstructed access to the headstock in only seconds with the Nova Swing-Away Lathe Attachment. This beefy cast iron hinge allows you to swing away your heavy tailstock along with your bed extension so you have full access to the headstock when turning bowls or hollowing out deep forms. The attachment fits the Nova 1624 and the Nova DVR XP lathes and Bed Extensions (48465, 45311 and 48218, all sold separately). Attach an extra bed extension accessory to your Nova lathe (1624 or DVR XP) for longer projects, then use the Swing Away accessory to move the extra bed piece out of the way when it is not in use.No need to keep mounting and removing your extra bed extension and/or tailstock.Saves you space without having to remove the extra bed length.Simply move the tailstock to the end of the lathe bed, then swing the bed and tailstock away to allow full access to the headstock.The perfect accessory for bowl turners, who often struggle with tailstocks.Solid cast iron.CAD designed and tested for optimum strength.Pieces are cast from a high grade cast iron with solid section thickness, designed to withstand extremely high stresses with practically no distortion.Weight: 4.61kgs/10.16lbs.For NOVA 1624 and DVR XP lathes only (48465 and 45311, sold separately).203mm/7.99" radius.180° of swing.

Nova G3 Comet II Reversible Chuck

Nova G3 Comet II Reversible Chuck
$179.99

The Nova G3 Comet II Chuck features a locking set screw that allows it to be used safely in reverse mode without the risk of unthreading. It is designed for the Nova Comet II Midi Lathe (46457, sold separately), but can be used on any lathe with a 1" 8-TPI RH thread. When used on non-reversing lathes, the set screw must be removed. Like the similar Nova G3, this chuck is a four-jaw, self-centering scroll chuck with a high-powered TuffLock grip for incredibly solid, vibration free performance. The single-handed operation means more time turning and less time setting up. It has less weight, and less overhang than the larger chucks-perfect for the Comet II lathe. The minimal 1.79" body length maximizes your distance between centers, and reduces stress on the spindle. Includes a set of 2" (50mm) jaws. Designed for the Nova Comet II Midi Lathe (46457, sold separately).Locking set screw lets you use the chuck in reverse mode. If your lathe does not have a reversing spindle, the set screw must be removed.Set screw can be removed to be compatible with the Jet 1221VS. (Note: Not recommended for reversing)1" 8-TPI RH/LH threading-fits the Comet II Midi Lathe.Up to 400mm/16" diameter swing capacity.Up to 350mm/14" diameter bowls using 50mm/2" Jaws (supplied with chuck).Up to 50mm/2" length spigots (using 50mm/2" Jaws (supplied with chuck).Full packaged weight is (std) 1.4 kgs/3.1 lbs.Locking screw allows the chuck to be used while the lathe is running in reverse mode.Small, compact design minimizes load on small spindles and bearings.Open back for easy cleaning.Precise, powerful hardened gear action with Tuff Lock technology.Single-handed operation with included chuck key.Able to take all Nova accessory jaws. However, please note: the larger accessory jaws in the Nova line are not recommended for use on the Nova G3 Comet II Chuck. For more information, see the offers for individual jaw sets.All Nova chucks are four-jaw, self centering scroll chucks for fast, secure setups.The four jaw design firmly grips both round and square wood.Quality materials.Precision machined in one operation from a solid steel block for optimal accuracy.Polished self metal finish to allow for closer tolerances and accuracy.Common accessory jaw fixing profile - compatible across all Nova chucks and accessories.Jaw slides made from high-tech copper fused steel for maximum hardness, wear, and self-lubricating properties.Special woodturning dovetail profile on jaws.Auto safety stop feature-jaw slides can't protrude past the chuck body.Comprehensive instructions.Common insert/adapter fitting is compatible across all Nova chucks.Safe Lock Woodworm screw included for fast mounting of rough timbers. 2-Year Warranty.

Nova G3 Insert Chuck

Nova G3 Insert Chuck
$167.99

The Nova G3 Chuck is a four-jaw, self-centering scroll chuck for Mini and Midi lathes with up to a 16" swing over the bed. It's an excellent high-powered geared chuck with TuffLock grip for incredibly solid, vibration free performance. The single-handed operation means more time turning and less time setting up. The Nova G3 has less weight, and less overhang than the larger chucks - perfect for smaller lathe spindles. The minimal 1.79" body length maximizes your distance between centers, and reduces stress on the spindle. This is an insert chuck, and requires you to purchase a dedicated Insert/Adapter for mounting on your lathe. Includes a set of 2" (50mm) jaws. Recommended for power workholding on lathes with up to a 400mm/16" diameter swing.Up to 350mm/14" diameter bowls using 50mm/2" Jaws (supplied with chuck).Up to 50mm/2" length spigots (using 50mm/2" Jaws (supplied with chuck) .Full packaged weight is (Std) 1.4 kgs/3.1 lbs.Features of Nova G3 Chuck:Small, compact design minimizes load on small spindles and bearings.Open back for easy cleaning. Precise, powerful hardened gear action with Tuff Lock technology.Single-handed operation with included chuck key.Able to take all Nova accessory jaws. However, please note: the larger accessory jaws in the Nova line are not recommended for use on the Nova G3 Insert Chuck. For more information, see the offers for individual jaw sets.Features standard on all Nova chucks: All Nova chucks are four-jaw, self centering scroll chucks for fast, secure setups.vThe four jaw design firmly grips both round and square wood.Quality materials. Precision machined in one operation from a solid steel block for optimal accuracy. Polished self metal finish to allow for closer tolerances and accuracy.Common accessory jaw fixing profile - compatible across all Nova chucks and accessories.Jaw slides made from high-tech copper fused steel for maximum hardness, wear, and self-lubricating properties.Special woodturning dovetail profile on jaws.Auto safety stop feature - jaw slides can't protrude past the chuck body.Comprehensive instructions.Common insert/adaptor fitting is compatible across all Nova chucks.Safe Lock Woodworm screw included for fast mounting of rough timbers.2-Year Warranty.

Bed Extension for Jet JWL-1015 and JWL-1015VS Lathes

Bed Extension for Jet JWL-1015 and JWL-1015VS Lathes
$149.99

Extend the turning capacity of your Jet JWL-1015 lathe (e.g. 47681, sold separately) from 15-1/2" to 36-1/2" with the JWL-1015 Bed Extension. The bed extension is built of the same heavy-duty cast iron as the lathe is, which means it soaks up vibration for extremely stable turning. Once the extension is attached, the lathe has a three-legged configuration which translates into excellent rigidity and resistance to sagging.Features:Increases distance between centers from 15-1/2" to 36-1/2".Heavy-duty cast iron construction for stability and less vibration.Once extension is installed, one leg of the 1015 lathe becomes a center leg, providing excellent support for the bed.

FastCap ChopShop Saw Hood

FastCap ChopShop Saw Hood
$139.99

Control messes created on the jobsite by sawdust and other debris with this heavy-duty water-resistant nylon hood. Hood creates a shell around chop saws, miter saws, lathes and wet saws to contain debris to a small area and prevent it from littering your entire work area. Also functions as a protective cover for equipment when working outdoors. Collapsible frame makes setup and take-down quick and simple. Hood dimensions are 42"W x 30"D x 31"H. Includes mounting hardware.

10'' Longworth Style Chuck

10'' Longworth Style Chuck
$139.99

Just rotate the plates of the Longworth Style Chuck and the soft silicone buttons close in almost instantly, and with perfect concentricity, to hold your project while you make the finishing cuts to the bottom side. Unlike many other rechucking methods, the silicone buttons won't mar your project or your finish. When compressed with the wing nuts, they expand to provide a secure grip. The 1/4" thick phenolic plates provide strength and stability, regardless of humidity. Available in two sizes: the 10" Longworth Style Chuck for mini and midi lathes with a 10" swing, and the 16" Longworth Style Chuck for standard-sized lathes with a 16" swing or larger. Pick up a piece of fine china, and the first thing you'll do after admiring the faceis turn it over to inspect the bottom and insignia. It's no different with turnedbowls, and turners work hard to make the bottom as beautiful as the top. Butchucking a finished bowl face down on the lathe without damaging it hasalways been a challenge - not with the Longworth Style Chuck. Simply rotatethe plates, tighten down the buttons, and you're ready to turn.Eliminates the time and inconvenience of installing, adjusting and readjustingordinary rechucking jaws.Capable of holding projects in compression or expansion mode (from theinside or outside of the rim of your turning project).Buttons close in concentrically, making it easy to center your project.Soft silicone buttons have increased length for better grip and expansioncapabilities.Buttons expand when the wing nut is tightened, and will not mark or deformyour turned piece.Includes 8 buttons. Replacement packs of buttons with hardware are availableseparately (47455).No assembly required.1/4" phenolic discs are extremely durable, stable, and spin in opposingdirections with almost no resistance.The back side of the Longworth Style Chuck has a steel disk approximately 3/8"thick for mounting.The disk is easily gripped by any brand of 4-jaw scroll chuck with the standard50mm #2 jaws.Straight jaws may be used, but dovetail jaws provide a better hold.The dovetail groove accommodates Nova chucks and Vicmarc chucks as well asOneWay type straight jaws.Recommended maximum RPM is 600.Intended for light finishing cuts only. Note for heavy stock removal. Note: Best practice for safety dictates that you engage the tailstock wheneverpossible. Remove the tailstock only when finishing the last bit in the very center,and for finish sanding.Specifications:Capacity in compression mode: 4-1/2" to 8" in diameter.Capacity in expansion mode: 5-3/4" to 9-1/2" in diameter.

Mega Jumbo Jaws for Oneway Stronghold Chuck

Mega Jumbo Jaws for Oneway Stronghold Chuck
$133.39

These machined solid aluminum plates mount to the Oneway Stronghold Chuck (30589, sold separately), and they have a unique combination of slots and tapped holes that accept rubber grippers for holding an infinite number of round, oval or square shapes.Chucking capacities of the Stronghold Chuck with Mega Jumbo Jaws:External (compression): 1-3/4" minimum, 14" maximumInternal (expansion): 4-3/4" minimum, 15" maximumNote: If your lathe has less than a 16" swing, the Oneway Talon Chuck (20761) is recommended. Stronghold Chuck jaws are NOT compatible with either the original Oneway Chuck or the Talon Chuck.

Nova Precision Midi 1" 8-TPI Direct Thread Chuck

Nova Precision Midi 1" 8-TPI Direct Thread Chuck
$130.99

The Nova Precision Midi Direct Thread Chuck is the smallest chuck in the Nova lineup-ideal for lathes with up to a 12" swing over the bed. Its small size minimizes the load on small spindles and bearings, yet is extremely accurate, and built to the same exacting standards as the SuperNova 2 and Titan Chucks. It also accepts the same accessory jaws as other Nova chucks. Features auto jaw stop, anti-seize copper composite jaw slides, Safe-Lock Woodworm Screw and 50mm Jaws as standard. Quick two-handled operation makes it ideal for fast production turning of smaller pieces. Recommended for power work holding on lathes up to 300mm/12" diameter swing. Up to 350mm/14" diameter bowls using 50mm/2" Jaws (supplied with chuck) Up to 50mm/2" length spigots (using 50mm/2" Jaws (supplied with chuck) Full packaged weight is (std) 1.3 kgs/3 lbs. Body size 85mm/3.35". Cannot be used with adapters/inserts.Features of Nova Precision Midi Chuck: Small, compact design minimizes load on small spindles and bearings. 2-Lever operation offers very fast action-ideal for production turning of small pieces. Made from precision machined 1045 high tensile steel. Able to take all Nova accessory jaws. However, please note: the larger accessory jaws in the Nova line are not recommended for use on the Precision Midi Chuck. For more information, see the offers for individual jaw sets. Features standard on all Nova chucks: All Nova chucks are four-jaw, self-centering scroll chucks for fast, secure setups. The four jaw design firmly grips both round and square wood. Quality materials. Precision machined in one operation from a solid steel block for optimal accuracy. Polished self-metal finish to allow for closer tolerances and accuracy. Jaw slides made from high-tech copper fused steel for maximum hardness, wear, and self-lubricating properties. Special woodturning dovetail profile on jaws. Auto safety stop feature''jaw slides can't protrude past the chuck body. Comprehensive instructions. Safe Lock Woodworm screw included for fast mounting of rough timbers. 2-Year Warranty.

Nova Comet II Bed Extension

Nova Comet II Bed Extension
$129.99

Extend the spindle turning capacity of your Nova Comet II Midi Lathe! This bed extension adds 25-1/2" in length, extending the Comet II's distance between centers to 42". You can also add multiple bed extensions for even longer turnings. Solid cast iron throughout for durability and vibration-free turning.

Stand Extension for Jet JWL-1015 and JWL-1015VS Lathes

Stand Extension for Jet JWL-1015 and JWL-1015VS Lathes
$129.99

This Stand Extension lengthens the Jet JWL-1015 Stand (49418, sold separately) in order to support the fully-extended Jet JWL-1015 lathe (e.g. 47681 with 46484, sold separately). The Stand Extension consists of a center leg and horizontal stretcher. Sturdy steel construction.Once the Stand Extension is combined with the Jet JWL-1015 Stand (49418, sold separately), three sturdy columns support your lathe from end to end.Center foot is adjustable for level.Sturdy steel construction.

Nova Mini Jaws Package

Nova Mini Jaws Package
$124.99

Get the complete suite of Nova mini jaws in one cost-saving package! The bundle consists of four sets of jaws: the Nova Mini 20mm Jaws, Nova Mini Spigot Jaws, Nova Mini Step Jaws and Nova 70mm Jaws. All are ideal for use with the Nova Precision Midi Chuck (47447, sold separately) mounted on a mini or midi lathe. However, they also work on the larger Nova chucks, and with larger lathes. All four jaws are also available individually. Includes four sets of Nova jaws:Nova JS20N Mini 20mm Jaws (Rockler #48448)Nova 6026 Mini Spigot Jaws (Rockler #48021)Nova 6025 Mini Step Jaws (Rockler #43751)Nova JS70N 70mm Jaws (Rockler #47450)Nova JS20N Mini 20mm Jaws (Rockler #48448):Capacity range when used with Nova Precision Midi chuck (47447, sold separately):Expansion mode: 0.79" to 1.63".Contraction mode (square stock): 0.39" to 0.79".Contraction mode (spigot): 0.32" to 1.18".Capacity range when used with Nova G3 chuck (45748, sold separately):Expansion mode: 0.79" to 1.63".Contraction mode (square stock): 0.39" to 0.79".Contraction mode (spigot): 0.32" to 1.18".Capacity range when used with NNova SuperNova 2 chuck (48906, sold separately):Expansion mode: 0.79" to 1.63".Contraction mode (square stock): 0.39" to 0.79".Contraction mode (spigot): 0.32" to 1.18".Capacity range when used with Nova Titan chuck (45040, sold separately):Expansion mode: 0.79" to 2".Contraction mode (square stock): 0.39" to 1.18"Contraction mode (spigot): 0.32" to 1.57".Nova 6026 Mini Spigot Jaws (Rockler #48021):Capacity range when used with Nova Precision Midi chuck (47447, soldseparately):Expansion mode (Step 1): 1.06" to 1.93".Expansion mode (Step 2): 1.45" to 2.28".Contraction mode (square stock; step 2 only): 0.36" to 1.1".Contraction mode (spigot; step 2 only): 0.41" to 1.24".Capacity range when used with Nova G3 chuck (45748, sold separately)Expansion mode (Step 1): 1.06" to 1.93".Expansion mode (Step 2): 1.45" to 2.28".Contraction mode (square stock; step 2 only): 0.36" to 1.1".Contraction mode (spigot; step 2 only): 0.41" to 1.24".Capacity range when used with Nova SuperNova 2 chuck (48906, sold separately):Expansion mode (Step 1): 1.06" to 1.93".Expansion mode (Step 2): 1.45" to 2.28".Contraction mode (square stock; step 2 only): 0.36" to 1.1".Contraction mode (spigot; step 2 only): 0.41" to 1.24".Capacity range when used with Nova Titan chuck (45040, sold separately):Expansion mode (Step 1): 1.06" to 2.32".Expansion mode (Step 2): 1.45" to 2.72".Contraction mode (square stock; step 2 only): 0.36" to 1.5".Contraction mode (spigot; step 2 only): 0.41" to 1.63".Nova JS70N 70mm Jaws (Rockler #47450):Capacity range when used with Nova Precision Midi chuck (47447, soldseparately):Expansion mode: 2.76" to 3.54".Contraction mode (square stock): 1.46" to 2.56".Contraction mode (spigot): 2.2" to 3".Capacity range when used with Nova G3 chuck (45748, sold separately)Expansion mode: 2.76" to 3.54".Contraction mode (square stock): 1.46" to 2.56".Contraction mode (spigot): 2.2" to 3".Capacity range when used with Nova SuperNova 2 chuck (48906, sold separately):Expansion mode: 2.76" to 3.54".Contraction mode (square stock): 1.46" to 2.56".Contraction mode (spigot): 2.2" to 3".Capacity range when used with Nova Titan chuck (45040, sold separately):Expansion mode: 2.76" to 3.94".Contraction mode (square stock): 1.46" to 2.95".Contraction mode (spigot): 2.2" to 3.43".Features standard on all Nova Jaws:Nova chucks give you the same jaw fixing system and same insert/adaptersystem across all chuck models.All accessory jaws in the range will fit allflexibility. Some, however, are not recommended. See individual jaws forrecommendations.Nova chucks are specially designed so the jaws cut into the wood, grip firmly in the contraction mode and provide high tear out strength.

Jumbo Jaws for Oneway Scroll Chuck System

Jumbo Jaws for Oneway Scroll Chuck System
$115.49

When mounted on the Oneway Scroll Chuck (22719, sold separately) or the Talon Chuck (20761, sold separately), the machined solid aluminum plates of the Jumbo Jaws form a plate 11" in diameter. With the rubber grippers and the combination of slots and tapped holes machined in the solid aluminum plates, the Jumbo Jaws can hold an infinite number of round, oval or square shapes.Chucking capacities of the Oneway Scroll Chuck with Jumbo Jaws:External (compression): 2-7/8" minimum, 11" maximumInternal (expansion): 4-7/8" minimum, 12" maximumChucking capacities of the Oneway Talon Chuck with Jumbo Jaws:External (compression): 2-7/8" minimum, 11" maximumInternal (expansion): 4-7/8" minimum, 12" maximum

CMT BTS-1 Bowl & Tray Router Bit System Kit- 1-1/4" Dia x 1/2" Shank

CMT BTS-1 Bowl & Tray Router Bit System Kit- 1-1/4" Dia x 1/2" Shank
$114.99

Whether for vegetable trays, salad bowls or hors d'oeuvre platters, this kit lets you make gorgeous divided bowls quickly and easily. No lathe? No problem. A band saw or jig saw can handle the outer circumference. For the interior, all you need is this kit and a router. The kit includes two templates, a Bowl and Tray bit, and a collet extension, full instructions and an instructional DVD. The end results will astonish your friends. And what great gifts they'll make in a very short amount of time!Bowls and trays made with this set provide an excellent use for scrap wood. Glue pieces together butcher block style to make a beautiful pattern of colors and species. The templates will withstand a lifetime of use, and with a little imagination they can be used to make several styles of bowls or trays. The DVD provides specific examples of how to modify your designs. The collet extension, used to make extra deep bowls, is also useful whenever your general woodworking requires extra deep cuts.Template material is 1/2" MDF (all templates are produced on a CNC router, ensuring perfect curves and straight lines).Oval template produces 14" wide x 22-1/2" long tray.Pie-cut template produces 16-3/4" round tray.3-1/2" long collet extension accepts 1/2" shank router bits.Bowl and Tray router bit: 1-1/4" diameter; carbide tipped; shear angle; 1/2" shank.Instructional DVD is 38 minutes long.

Jumbo Jaws for Oneway Stronghold Chuck

Jumbo Jaws for Oneway Stronghold Chuck
$110.29

The Jumbo Jaws for the Oneway Stronghold Chuck (30589, sold separately) consist of plates machined from solid aluminum. Their combination of slots and tapped holes accept rubber grippers for holding an infinite number of round, oval or square shapes.Chucking capacities of the Stronghold Chuck with Jumbo Jaws:External (compression): 2-3/4" minimum, 11" maximumInternal (expansion): 4-3/4" minimum, 12" maximumNote: If your lathe has less than a 16" swing, the Oneway Talon Chuck (20761) is recommended. Stronghold Chuck jaws are NOT compatible with either the original Oneway Chuck or the Talon Chuck.

Pages: first pageprev page1 2 3 4 5 6 7 8 9 10next pagelast page