Pages: first pageprev page5 6 7 8 9 10 11 12 13 14next pagelast page

EZSmart Repeater Set

EZSmart Repeater Set
$179.99

Traditional track saw systems require you to measure and mark the stock, then manually align the guide rail with your markings before you make your cut. Not so with this Repeater Set and your EZSmart Track Saw System (e.g. 57811, sold separately). Once installed, you have two telescoping arms with pivoting stops on either end of your guide rail. The stops register against the edge of your material for accurate, repeated cuts. No tapping the rail to align it with your marks, just slide it up against the stops and make your cut. Made in USA. Enables easy, repeateable straight or tapered cuts without measuring and markingInstalls easily without the need for toolsCut at any dimension from 0'' to 30''Does not damage material surfacesMade for a lifetime of commercial use

Forrest 10" x 80T Duraline Melamine and Plywood Saw Blade

Forrest 10" x 80T Duraline Melamine and Plywood Saw Blade
$169.99

You'll get faster feed rates plus absolute splinter control- even on Oak/Birch ply veneers and melamine! Gives you refined cuts every time. The double hard C4 carbide teeth and high angle alternate tooth bevel (HiATB) design of the Forrest Duraline blade give you extra-clean cuts in melamine, hard and soft wood, and veneered plywood.

Fein Flush Cut Saw Blade 3-11/32''

Fein Flush Cut Saw Blade 3-11/32''
$169.99

For use with the Fein MultiMaster, the Flush Cut Blade has a depressed center so you can cut squarely against flat surfaces. Use for plastics, fiberglass, wood, putty, non-ferrous metal and sheet metal, flush to the surface.

10-Piece Avenger Carbide Hole Saw Set

10-Piece Avenger Carbide Hole Saw Set
$169.99

If you've ever used a traditional hole saw, these carbide hole saws will be a revelation. They churn out quick, clean holes, with no burning or smoking, and the tapered pilot bits make removing the plug an easy task. With Carbide Hole Saws, the thick cutters sit proud of the cylinder, maintaining a generous air pocket that keeps it cool, and also provides some wiggle room so the drop-off piece doesn't get stuck. Carbide hole saws also make an excellent alternative to forstner bits, as unlike the latter, they can be used in a hand drill as well as in a drill press. This set of carbide hole saws includes the following sizes: 2'', 1-3/4'', 1-1/2'', 1-3/8'', 1-1/8'', 1'' and 3/4'' in diameter.Features:Solid carbide teeth create an air pocket around the hole saw, eliminating burning and smoking.Tapered pilot bits make it easy to remove the drop-off piece, since they naturally release as the plug is removed.Can be used with a hand drill or a drill press.Arbors come with replaceable tapered pilot bits pre-installed.Larger arbor features studs that engaged with the hole saw to prevent slippage.Includes the following hole saw sizes: 2'', 1-3/4'', 1-1/2'', 1-3/8'', 1-1/8'', 1'' and 3/4'' in diameter.

EZSmart Track Saw System

EZSmart Track Saw System
$169.99

The EZSmart Track Saw System gives you absolutely straight cuts with virtually zero tear-out or chipping-all with the circular saw of your choice! Unlike many similar systems, this one includes a Universal Saw Base that can be fitted to over 90% of left- or right-bladed circular saws. That means there's no need to pay a premium for a specialty saw. The saw glides effortlessly down the rail for rip cuts, cross cuts, and angle cuts. Thanks to the guide rail's zero-clearance edges and the chip-free inserts on the bottom of the base, the cut quality is far better than typical table saws. And since the wood is captive under the track, there is no danger of kickback. Includes two EZSmart Clamps capable of securing even the smallest boards under the track. If you want an even longer guide rail, additional Guide Rails (55763 and 50438) and Connectors (one of 57360 and two of 56171 will be required) are available separately. Made in USA. Included Universal Saw Base can be fitted to over 90% of left- or right-bladed 6-1/2'', 7-1/4'' and 8-1/4'' circular sawsGuide rail is bi-directional, and features two anti-chip edges-use one for 90° cuts, the other for bevel cutsPatent-pending anti-chip inserts provide zero clearance on either side of the blade for astoundingly clean cutsDanger of kickback is all but eliminated by the included anti-kickback fin, which prevents the material from bindingNo more lugging around a heavy table saw to job-sites; get proven results with this lightweight kitIncludes anti-chip inserts for use either on the guide rail or off

Rockwell Jawhorse HD RK9003 Workbench System - As Seen on TV!

Rockwell Jawhorse HD RK9003 Workbench System - As Seen on TV!
$166.99

As seen on TV, this heavy-duty hands-free clamp not only secures workpieces with a rock-solid grip, its wide stable frame instantly provides a go-anywhere workstation to make cuts, drill holes, and more. Hold and cut doors, two-by-fours, two-by-twelves, and odd-shaped objects. Mount miter saws, tile saws, grinders and other tools to wood panels and use the Jawhorse as a sturdy stand. Clamp in a vertical support piece and install crown molding all by yourself. Do it all and more with this incredibly versatile tool that also folds up for simple storage and transportation.With a solid steel frame, no moving plastic parts, and a hardened metal ratcheting system, the Jawhorse is built to last. It's also extremely portable and easy to use; simply engage the clamp with the foot lever to apply over one ton of clamping force!

Bosch JS470EB 7.0A Barrel-Grip Jigsaw

Bosch JS470EB 7.0A Barrel-Grip Jigsaw
$164.99

As the original developer of the handheld jigsaw, Bosch has always been on the cutting edge of jigsaw technology. The JS470 continues this tradition with a powerful 7 amp motor for smooth, easy cutting, and Constant Response circuitry that maintains the desired speed under heavy loads. Bosch's unparalleled blade change system lets you quickly swap blades without tools, and you can even eject hot blades without having to touch them. Blade speed is variable from 500-3100 SPM, and four orbital action settings let you vary the stroke pattern from straight up and down for fine, low-splinter cuts, to strongly orbital cuts that sail through the toughest materials. The lock-on button is ambidextrous, and the saw also includes a dust blower to keep the cut line visible. Features:Powerful 7.0-amp motor.Variable speed dial sets operating speed.Constant Response circuitry maintains desired speed for consistent performance and precision.Aluminum gearbox with insulated cover.Ergonomic body with upfront softgrip area for maximum comfort and control.Toolless blade-change system for fast blade changes.Blade ejection lever eliminates need to touch hot blade.Precision-machined plunging system and low-vibration design for enhanced accuracy and extremely smooth operation.Large, sturdy die-cast foot with steel insert and on-board bevel adjusting wrench.Exclusive multi-directional blade clamp provides superior grip of T-shank blades (does not accept U-Shank blades).Four orbital-action settings for smooth to aggressive cuts.Adjustable dust blower keeps cutting line clear.Ambidextrous lock-on button for comfort during long cuts.

Dewalt DWS5023 102'' Track Saw Track

Dewalt DWS5023 102'' Track Saw Track
$164.99

102" Track Saw Track3 Year Limited WarrantyIncludes:DWS5023 102" TrackFeatures & Benefits:Zero clearance TrackSaw cutting system delivers precise, straight, splinter-free cuts.TrackSaw dual-edged tracks for perfectly straight cuts in both directions.

SawStop Mobile Base for CNS Table Saws

SawStop Mobile Base for CNS Table Saws
$160.00

This SawStop Mobile Base will add versatility and convenience to your SawStop CNS Table Saw. Featuring durable polyurethane wheels, two fixed-direction wheels and two 360° casters for easy positioning.Fully-welded 1/4" rigid steel constructionHard-wearing, black powder coat finishEasy-to-follow assembly instructionsEasy one-foot operationSupports entire table and requires no extension piece - even for the 52" extension tableTechnical DetailsSawStop Part#: MB-CNS-000Length: 27"Width: 13"Height: 7"Best Used With:SawStop Contractor Table Saw w/30" FenceSawStop Contractor Table Saw w/36" FenceSawStop Contractor Table Saw w/52" Fence

Incra Miter Express Miter Sled

Incra Miter Express Miter Sled
$159.99

Upgrade any miter gauge to a miter sled in seconds!Makes cutting multiple pieces with precision a snap.Safely doubles any miter gauge's crosscut range up to 24" and eliminates all side play to improve your miter gauge's performance.True zero-clearance tearout control on both sides of the table.Works with any brand of miter gauge. Miter gauge not included.For extra-large crosscuts, the non-drag support provided by the sliding panel - along with the extra holding power of the included hold-down clamps - adds stability and control.Incra hold-down clamp keeps your fingers away from the blade when cutting small workpieces.Includes outboard fence support that locks behind your fence in T- slot to provide even more rigidity for all operations.Instantly removable from your table saw when making rip cuts or other operations that don't require a sled.Safely handles large and extra small workpieces.Excellent crosscut and mitering control.Comes with hold-down clamp and aluminum miter bar.With quick-release feature.Works with any miter gauge in your shop!The Miter Express features removable front and rear T-Slot Retaining Clips for sled stability at both the beginning and end of long crosscuts.

Incra Miter 1000SE with Telescoping Fence

Incra Miter 1000SE with Telescoping Fence
$159.99

Achieve mitering accuracy that you never thought possible! Special Edition miter gauge comes with sturdy telescoping fence and dual-arm Flip Shop Stop for accurate miter cuts on the table saw or router table.Precision angle indexing teeth are laser cut in solid steel to lock in 41 positive angle stops in 5° increments over a full 180° range, with special stops at 22-1/2° and 67-1/2°.Stainless steel vernier cursor delivers an incredible 1/10° resolution between fixed steps.Get perfect, repeatable accuracy every time - whether making basic 90° cut-offs, simple picture frames, complex compound miters, or a 20-sided object.Incra precision allows you to produce perfect, gap-free hairline glue joints on the mitered corners of any multi-sided object without trial-and-error setups.Sturdy Special Edition Incra-Lock fence telescopes from 18" to a full 31" length.Flip Shop Stop has patented saw tooth rack system that instantly controls the length of your cut. Dual flip arms, equipped with three sliding stop rods, operate independently or in tandem for one, two or three simultaneious stop positioner setups. Made of solid aluminum with hardened anodized surface.Miter bar has six expansion disks to adjust both sides of the bar for zero side play and anti-friction travel on all table saws and router tables with standard 3/8" x 3/4" miter slots.Interlocking tongue-and-groove cooperation between the flip arms and surface of the fence insures that the sharp end of a mitered board won't wedge itself between the fence and the stop.

Vertical Panel Saw Extensions

Vertical Panel Saw Extensions
$159.99

Sold as a pair, these extensions add 20" to each side of the material-handling roller fence of the Safety Speed Cut Vertical C4 Panel Saw (25474, sold separately), allowing for easy processing of larger panels.

Bosch JS470E 7.0A D-Handle Jigsaw

Bosch JS470E 7.0A D-Handle Jigsaw
$159.99

As the original developer of the handheld jigsaw, Bosch has always been on the cutting edge of jigsaw technology. The JS470 continues this tradition with a powerful 7-amp motor for smooth, easy cutting, and Constant Response circuitry that maintains the desired speed under heavy loads. Bosch's unparalleled blade change system lets you quickly swap blades without tools, and you can even eject hot blades without having to touch them. Blade speed is variable from 500-3100 SPM, and four orbital action settings let you vary the stroke pattern from straight up and down for fine, low-splinter cuts, to strongly orbital cuts that sail through the toughest materials. The lock-on button is ambidextrous, and the saw also includes a dust blower to keep the cut line visible. Features:Powerful 7.0-amp motor.Variable speed dial sets maximum speed.Constant Response circuitry maintains desired speed for consistent performance and precision.Aluminum gearbox with insulated cover.Toolless blade-change system for fast blade changes.Blade ejection lever eliminates need to touch hot blade.Precision-machined plunging system and low-vibration design for enhanced accuracy and extremely smooth operation.Large, sturdy die-cast foot with steel insert and on-board bevel adjusting wrench.Exclusive multi-directional blade clamp provides superior grip of T-shank blades (does not accept U-Shank blades).Four orbital-action settings for smooth to aggressive cuts.Adjustable dust blower keeps cutting line clear.Ergonomic top handle with soft-grip areas for solid, comfortable grip.Ambidextrous lock-on button for comfort during long cuts.

Rockler 24'' x 36'' Shop Stand

Rockler 24'' x 36'' Shop Stand
$159.99

The perfect steel stand for your CNC Shark, workbench, assembly table or machining station. Legs and stretchers are pre-drilled to easily add sides, bottom and hinged doors for a built-in cabinet and have square holes for easy assembly with carriage bolts. Legs are heavy-duty 1/8" steel, with adjustable levelers for various height settings. Top stretchers can be mounted flush with top or 4" down to add drawer or vise. All parts coated with durable black sand paint.Technical Details:Steel base measures 24"W x 36"L x 32"H.Perfect for a CNC table, work station, workbench, assembly table, or tool stand!Use with your CNC router, grinder, sander, router table, scroll saw, chop saw and more!All legs and stretchers are pre-drilled to easily add sides, bottom and hinged doors for a built-in cabinet, and have square holes for easy assembly with carriage bolts.Legs are heavy-duty 1/8" steel to support any shop application.Includes 4" x 1/2" heavy-duty adjustable levelers for various height settings.Includes four 32" legs and all mounting hardware (carriage bolts and nuts).Top stretchers can be mounted flush with top or 4" down to add drawer or woodworking vice.All parts coated with durable black sand paint.

Rockler Horizontal Panel Router Bit Set With Wooden Case

Rockler Horizontal Panel Router Bit Set With Wooden Case
$149.99

This rail-and-stile set includes everything you need to create raised-panel doors of nearly any size. The stile and rail cutters are full-height cutters. This means that if you jog your router table fence, they can be used to joint off saw marks '' no need to sand or joint before routing. In addition, they feature guide bearings for template work such as arch-top doors. The panel raiser features a 5/8" radius ogee profile that goes well with the beaded profile on the stick work. All bits have sturdy 1/2" shanks for minimal chatter.

Rockler Vertical Panel Router Bit Set With Wooden Case

Rockler Vertical Panel Router Bit Set With Wooden Case
$149.99

This rail and stile set includes everything you need to create raised panel doors of nearly any size. The panel raiser is vertically oriented, which is ideal for smaller routers, and features a 5/8" radius ogee profile that goes well with the beaded profile on the stick work. The stile and rail cutters are full height cutters. This means that if you jog your router table fence, they can be used to joint off saw marks—no need to sand or joint before routing. In addition, they feature guide bearings for template work such as arch-top doors. All bits have sturdy 1/2" shanks for minimal chatter.

All-In-One Clamp Guide Package w/Free Squaring Attachment

All-In-One Clamp Guide Package w/Free Squaring Attachment
$149.99

This package includes three All-in-One Clamp Guide lengths (24", 36" and 50") PLUS an accessory set of wide jaws for fast, accurate squaring of the clamp guides. You can attach your own wooden cauls to the squaring jaws in whatever length you need to achieve even more accurate squaring. The All-in-One Clamp Guides are rigid, lightweight, and boast zero-deflection for laser-straight cut lines. They feature a low-profile design with zero obstructions that would interfere with the path of your tools. They make ideal straight-edge saw guides, router guides, measuring tools, marking aids and, of course, clamps. Expertly engineered, they are easy to attach and to adjust - just close the four-position locking lever, and you're ready to go.Squaring Attachment:Squaring attachment consists of two extra-wide aluminum jaws that provide increased reference surface to keep your Clamp Guides perpendicular to the edge.Jaws measure 7/8'' high x 3-3/4'' wide.Jaws include screws and pre-drilled holes for attaching additional additional wooden cauls for even better accuracy.Compatible with A and C Series All-In-One Clamp Guides.All-In-One Clamp Guides:A straight edge guide that's simple to adjust.Integral clamping jaws and locking lever provide a quick, easy way of clamping the guide.Four lever positions for variable clamping strength.Two clearly labeled scales in 1/8" graduations.Wide body construction (2-1/2") adds beam strength for added stability.Low-profile design and flat top for bearing-guided routing applications.Built-in T-track on top of the guide allows you to use any of our versatile accessories or shop-made jigs.Create your own shooting board for routing or cutting with the circular saw.This is a "C Series" or Contractor series clamp with a lower profile. "A Series" accessories will not work with this model.To engage the jaw the first few times, the "I"-shaped blue finger-grip MUST be pushed snug against the sliding jaw for the jaw to lock. Squeeze together until it clicks. Then push the finger-grip AWAY from the jaw to unlock the sliding jaw.

Vertical Panel Saw Folding Stand

Vertical Panel Saw Folding Stand
$149.99

This folding stand allows the Safety Speed Cut Vertical C4 Panel Saw (25474, sold separately) to be free-standing, so the unit doesn't need to be leaned against a wall.

Pages: first pageprev page5 6 7 8 9 10 11 12 13 14next pagelast page