Pages: first pageprev page3 4 5 6 7 8 9 10 11 12next pagelast page

Kreg Jig HD Heavy-Duty Pocket Hole System

Kreg Jig HD Heavy-Duty Pocket Hole System
$59.99

Go BIG with the Kreg Jig HD Heavy-Duty Pocket Hole Jig-a supersized, industrial-strength Kreg Jig optimized for working with 2x4 stock and larger. With all of the famed speed of the original Kreg Jig, along with robust joints that are 50% stronger, and big 2-1/2" weather coated #14 screws, the Kreg Jig HD makes a simple, strong joinery system for wall framing, deck railing, outdoor furniture, gazebos, swings, fences, trellises and anything else that will need to stand the test of time and the elements. The Kreg Jig HD is extremely portable for job-site use, simply slip your Kreg Face Clamp (sold separately, 26613), into the jig and lock it into place for a one-piece system. Or, if you'd like to use it in the shop, you can also slip it into the benchtop base of the Kreg K3 and K4 jigs (sold separately, 27204) for upright drilling.Technical Details:Designed with the same tried-and-true efficient design and hardened steel drill guides as the original Kreg Jig.The Kreg Jig HD lets you drills holes which are 25% larger, and joints that are an amazing 50% stronger than traditional Kreg joints.The Kreg Jig HD is optimized for working with 2x4s and larger stock - anything 1-1/2" thick or thicker.Utilizes #14 industrial-quality, heavy-duty, hardened-steel screws, which provide incredible shear resistance as well as 3 anti-corrosion layers for incredible long-term moisture resistance.The Kreg Jig HD works great as a stand-alone jig; simply connect it to your Kreg Face Clamp (sold separately, 26613), lock it into place, and take it wherever you need to go.Depending on the project, the Kreg Jig HD can also connect directly to your model K3 or K4 Kreg Jig benchtop base (sold separately, 27204) for uprightdrilling.

Rockler 45° Lock Miter Router Bits - 1/2'' Shank

Rockler 45° Lock Miter Router Bits - 1/2'' Shank
$57.99

The interlocking fingers of our Lock Miter Router Bit provide a strong mechanical locking action that makes it much easier to clamp. There is no tendency for the joint to slide out of alignment under clamping pressure, and the wedged tenons tighten up nicely for a strong corner joint. The increased long grain gluing surface also helps to strengthen the joint over a basic rabbet or butt joint. Machining parts with the Lock Miter Bit is easy''with the bit height set, one part is cut horizontally on the router table, while the corresponding part is cut vertically. The bit is ideal for joining drawer boxes, cabinet parts, and for building 4-sided columns.Note: To make setting the cutter height easy and fool-proof (Applicable for Item 22627), use the Rockler Router Bit Set-up Jig (53817, sold separately) to center the bit on your stock.

Long Knife Jig SVM-140 for Tormek T-7 Sharpening System

Long Knife Jig SVM-140 for Tormek T-7 Sharpening System
$56.00

This jig is made especially for long and thin knives. It works in the same way as the SVM-45 jig but it is wider and therefore gives more support to long and thin blades. The jig rests on the Universal Support. The exact edge angle is set by rotating the stop or with the Micro Adjust on the Universal Support. The Universal Support is placed vertically for grinding towards the edge.The jig comprises an adjustable clamp for holding knives of any thickness and an adjustable stop. You adjust the jig to the knife thickness with the screw. You lock the tool by tightening the knob.Best Used With:35254 -Tormek T-7 Sharpening SystemClick Here to View Instructions:

35mm Euro Hinge Jig Bit

35mm Euro Hinge Jig Bit
$55.99

Replacement 35mm hinge cup drill bit for use with the 35mm Euro Hinge Drilling Jig (30337, sold separately).

Rockler 4-Pc. Dovetail Router Bit Upgrade Set - 8mm Shank

Rockler 4-Pc. Dovetail Router Bit Upgrade Set - 8mm Shank
$54.99

This router bit set features 8mm shanks, which are 25% larger than 1/4" bits. The extra mass in the shank helps to reduce chatter. Ideal for joining case goods, the set includes 1/2" x 14° and 8° dovetail bits, a 5/16" straight bit, and 1/2" to 8mm collet adapter. The straight bit can be used for box joints, or for cutting grooves and dados. Fits all existing Rockler dovetail jigs.

Bench Cookie Plus T-Track Kit

Bench Cookie Plus T-Track Kit
$54.97

T-tracks are renowned for their adjustability, and Bench Cookies for their versatility - now this complete kit allows you to combine the two for the ultimate in both! T-Track Risers slide conveniently into your T-track to provide a set of four elevated posts for your Bench Cookie Plus Work Grippers. Not only do you get a no-slip, no-mar work surface that is fixed firmly in place, but the additional height creates space for saw blades and router bits beneath the workpiece. Simply spin the Bench Cookies and they tighten themselves down, then add a final cinch for good measure.Bench Cookie Plus T-Track Kit Includes:Bench Cookie Plus Work Grippers, 4-PackBench Cookie Plus 2" T-Track Risers, 4-Pack17-Piece Universal T-Track KitTo enhance the versatility of this kit even further, purchase the T-Track Intersection Kit (#22209 - Sold Separately).Bench Cookie Plus Work Grippers:Lift, grip, and protect at a higher level with Rockler's Bench Cookie Plus Work Grippers!Newly redesigned, these high-friction rubber pads hold your project rock-steady while sawing, sanding, or routing without the use of clamps.New design features a 3/4" insert for various riser systemsBench Cookie Plus 2" T-Track Risers:Simply spin the Bench Cookies onto the T-Track Risers via the 3/4" insert.Risers are made of aluminum with a grooved surface.2-1/2" T-bolts work with Rockler Universal T-Track Kit (included) and virtually any other T-track.Riser bushings measure 2" long.17-Piece Universal T-Track KitOutfit your workbenches, jigs, or machine tables with the ultimate accessory track!Universal T-Track boasts a unique stacked-slot design that allows you to attach any accessory with 1/4" T-bolts, 5/16" T-bolts, or 1/4" Hex-bolts.17-Piece Kit Includes: one 4' length of Universal T-Track, two 3-1/2" x 5/16" T-bolts, two 1" x 5/16" T-bolts, two 1-1/2" x 5/16" T-bolts, two 2-1/2" x 5/16" T-bolts, four T-knobs, and four 5-star knobs.

Scissors Jig SVX-150 for Tormek T-7 Sharpening System

Scissors Jig SVX-150 for Tormek T-7 Sharpening System
$54.00

Puts the maximum sharpness on all sizes of scissors and shears. The jig for scissors sharpening comprises a support plate and a holder with two clamps for the scissors. Usually you use only the right clamp. For large scissors and garden shears you use both clamps. You adjust the clamp to fit the scissors' thickness with the screw. You lock the scissors by tightening the knob. The support plate has a sliding surface, so the holder with the scissors can easily be moved while it is pressed onto the plate.Best Used With:35254 -Tormek T-7 Sharpening SystemClick Here to View Instructions:

Rockler Clamp-It Assembly Square 6-Pc. Kit

Rockler Clamp-It Assembly Square 6-Pc. Kit
$52.99

Includes everything needed to easily clamp two corners at a time: two original Clamp-It Assembly Squares and four 5" Clamp-It Bar Clamps. Bar Clamp is held in place on the Clamp-It Assembly Square with a friction fit to make operation quick, easy and one-handed.Technical Details:Ideal for picture frame joinery, RTA assembly, drill press jigs and adding a shelf.Rigid polycarbonate.Assembly Square measures 8" x 8" x 1-1/2".5" Clamp-It Clamps feature fixed heads with comfortable ergonomic handles.Clamps have fixed heads with movable tail pieces.Bar has anti-slip detents to prevent slippage when tightening.Throat depth is 3/4" to clamp center on the assembly square.Maximum clamping thickness when used with the Clamp-It Assembly Square is 2-1/2".Maximum clamping thickness without assembly square is 4-1/2"

Deulen Planer & Jointer Sharpening Jigs-Sharpening Jigs

Deulen Planer & Jointer Sharpening Jigs-Sharpening Jigs
$52.99

Deulen Sharpening Jigs eliminate the cost and down-time of sending your jointer and planer knives away for sharpening, AND they bring the "scary sharp" sandpaper sharpening method to power tools. The process couldn't get any simpler. Just pop your planer or jointer knives into the two brass slots, cinch down the lock nuts, and with a few strokes on progressively finer sheets of sandpaper, you'll have an edge that rivals that of the finest handplanes. The jigs are available in 6" and 12" lengths for knives up to 16" in length, and the jigs can also be doubled up for longer knives. 18" long strips of PSA sandpaper are available below to be adhered to your own piece of plate glass, granite, or other flat sharpening surface.Technical Details: 6" Deulen Sharpening Jig handles knives up to 8" in length.12" Deulen Sharpening Jig handles knives up to 16" in length.For longer knives, the sharpening jigs can be piggy-backed. A progression of grits from 120 to 400 grit sandpaper is recommended for optimum sharpness.3-blade jointer knives can also be sharpened. If the knife is 8" or less, the 12" Deulen Sharpening Jig can handle three blades at once. For larger planer knives with three blades, a how-to video is included with a simple rotation system to ensure the knives are all sharpened equally.

Leigh Louver Door Guides

Leigh Louver Door Guides
$51.99

Now you can use your FMT to make precise louver doors with standard 1/4" x 1-1/4" louvers at a 45° angle. Matching tenons can be routed on the ends of louver stock or radiused louver stock can be routed to fit the mortise. Sold in left and right matching pairs. Note: New FMT guides not exactly as shown.

Rockler Large Box Spline Jig

Rockler Large Box Spline Jig
$49.99

Cutting decorative splines for large boxes that can't be machined on the router table is easy with the Rockler Large Box Spline Jig! This jig clamps to the outside corner of your box or chest to provide a precise 45° sliding surface for your router. The jig's fence is adjustable so you can align the cut line with the center of your particular router. Once set, operation is simple. Just position the jig, clamp and rout. For very large boxes, space is provided for clamping cauls that can span the width of the workpiece. Try different router bits-straight bits, V-groove bits, dovetail bits and more-to achieve different effects! Adjustable fence aligns the jig with your particular router's baseCorner relief protects delicate corners and ensures a tight fit to the workpieceCentering line makes aligning the cut quick and simpleLarge clamping areas can accommodate cauls for the biggest boxesHang hole for convenient storage when not in useMade of durable ABS plastic with engineered structural strengthInstructions included

Kreg Protec-Kote Deck Screws

Kreg Protec-Kote Deck Screws
$49.99

A trio of anti-corrosion layers protect these screws from rust as they hold your deckboards in place. Recommended for use with ACQ treated lumber.Designed for theKreg Deck Jig System (36613, sold separately) with self-tapping tips and KTX squaredrive heads.

Work Sharp WS3000 Tool Bar Attachment

Work Sharp WS3000 Tool Bar Attachment
$49.99

Improve the freehand sharpening on the top and underside of your grinding wheel with the Tormke Work Sharp WS3000 Tool Bar Attachment! Designed to accept a wide range of Tormek or Jet sharpening jigs (Sold Separately) for turning tools and carving tools. Fits all WS3000 tools, installs quickly and doesn't interfere with other attachments or operations of the tool. Cast metal bracket and a steel tool bar are rigid and provide a stable platform for freehand sharpening or the use of sharpening jigs. Micro-Adjust Nut provides precise Tool Bar positioning and repeatability. Provided Set Up Fixture creates consistent and repeatable tool set ups for fast and easy sharpening results. Coarse P80 grit abrasive included for shaping and sharpening tools.Note: Gouge Sharpening application pictured shows Short Tool Jig 27774 (Sold separately)

Master Plate with Super Bar

Master Plate with Super Bar
$49.99

Tune up your table saw to the peak of perfection.Tune up your table saw to the peak of perfection.Get the highest degree of accuracy with this combination Master Plate and Super Bar. Together, they help you tune-up, calibrate, and align your table saw to within 1/1000 of an inch! What's more, it promotes safer operation by helping to eliminate kickbacks, sticking, and binding. The master plate is made of solid 1/4" thick, flat-ground aluminum. It replaces your saw blade and bolts into a 5/8" or 1" arbor to provide a full 10" of near-perfect flatness for aligning your equipment. The Super Bar jig has an-onboard precision dial indicator that measures alignment as it slides in the miter gauge slot. This enables you to keep the saw blade parallel, align the fence, square tour protractor, and check runout on routers, drill presses, and more!

Vacuum Box kit for the Super FMT

Vacuum Box kit for the Super FMT
$49.00

Control debris for cleaner operation of your Leigh Super FMT Jig. Kit contains the Vacuum Box and two hose adapters for hoses from 1" to 2-1/2" in diameter.

Rockler Dust Collector for Rockler Dovetail Jigs

Rockler Dust Collector for Rockler Dovetail Jigs
$47.99

Finally, an affordable dust collection attachment for your Rockler dovetail jig! You don't have to spend hundreds of dollars to get dust collection with a dovetail jig. Our revolutionary new dust collector eliminates virtually all the dust created when cutting dovetails. It easily attaches to Rockler's dovetail jigs (both new and old!) and a shop vacuum or dust collection system to provide you with a clean cutting area and safe working conditions.Easily attaches to Rockler's dovetail jigs Built-in 2-1/4" port fits most shop vac hoses (not included).Sliding baffle directs the dust collection to where the dovetails are being cut.Sweep brush adjusts to provide a complete seal for stock thicknesses of 1/2" up to 1-1/8".Contains the dust while allowing the bit to travel through without damage.Two extra long 4" knob posts make adding your dust collector shroud easy.Built-in 2-1/4" port fits most shop vac hoses (not included).For older Rockler dovetail jigs with 4-screw side stops, conversion kit #25174 is required. (Sold out and no longer available).Patent pending.

EasyCoper for Crown Molding

EasyCoper for Crown Molding
$47.99

Take the guesswork out of coping crown molding to create perfect inside corners! Allows you to quickly and easily cope crown molding with a power jig saw instead of a coping saw, reducing wrist, hand and arm stress.Coped crown molding is actually one piece of crown fitting over the other piece, instead of the two being mitered at the inside corner.Handles up to 5-1/2" molding.Durable plastic.Sold in pairs. Left and right included in set.

Universal Support with Micro Adjust Upgrade (for Older Models) (US-105)

Universal Support with Micro Adjust Upgrade (for Older Models) (US-105)
$45.00

The versatile Universal Support is the basis of the Tormek system, and this upgrade for older models incorporates a micro adjust feature for exact and fast fine setting. It is made of 12mm (approx. 1/2") round steel and has a double mounting for maximum stability.The Universal Support can be placed either in the vertical sleeves or in a horizontal base. These two positions enable you to grind either toward or away from the edge. The Universal Support can also be placed horizontally for honing with jigs, but honing must always be done with the wheel turning away from the edge.

Pages: first pageprev page3 4 5 6 7 8 9 10 11 12next pagelast page