Bosch Self-Leveling Cross-Line Laser, 30' Range

When you need a level or plumb reference line on your wall, ceiling or floor, this cross-line laser indicator will save you loads of time. Rather than hauling out your level, tape measure and chalk line, you can simply push a button, and the unit projects a plumb line, a level line, or both in the form of a set of crosshairs. Use it to install cabinets, trim, molding, wainscoting, and even for simple household tasks like hanging artwork. The laser is self-leveling and includes an adjustable mounting device that lets you clamp it to whatever surface is convenient: a table, countertop, or the steps of a ladder. It can also be threaded onto the Bosch Compact Tripod (52320, sold separately). Three modes: horizontal line, vertical line and crosshairsOne button toggles between the three modes, and also turns the device on and offFlexible mounting device conveniently clamps to multiple surfaces for quick and easy setupSmart pendulum leveling system self-levels and indicates when unit is out-of-levelSwitch locks leveling mechanism for transport

$79.00
Buy
 

Related Products

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table
$8,629.99

The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch

Rockler Bandy Clamp, Pair

Rockler Bandy Clamp, Pair
$19.99

You'll find it easier than ever to clamp edge moldings of almost any contour with our clever new Bandy Clamp edge clamps. The Bandy Clamp combines the easy one-handed operation of a spring clamp with the even pressure and no-mar qualities of a super-tough rubber band. Just open the clamp and stretch the band over your edging material-the deeper you set it, the tighter the pressure. Once the Bandy Clamp is in place, its jumbo ultra-grippy clamp pads simply will not slip, allowing all the clamping force to be transferred into the material. Since every contact point is a no-mar surface. the clamp is ideal for delicate moldings, even from soft materials like white pine. What's more, the clamp works great for keeping power cables, extension cords and pneumatic lines out of your way as you work. You'll find countless uses for it around the house as well as the shop! Proprietary 1'' wide rubber band is made from a tough, tear-resistant material, with three extra-strength splines molded into itLarge, ultra-grippy clamp pads hold tight without slippingPivoting jaws accommodate angled pieces and allow full pad contact regardless of stock thicknessTo adjust tension, simply stretch the clamp further into the materialEasy cleanup-wood glue flakes right off the rubber band materialRubber band conforms to any shape and will not mar delicate materialsAlso works great for cord management tasks like storing extension cordsSpring clamp is made of high-strength nylon with fiberglass fill for added durabilityHandles are over-molded with an easy-to-grip rubber for greater comfort and control

Small Toggle Clamp

Small Toggle Clamp
$13.99

Once attached to a bench or fixture, this clamp is simple to use and ideal for light-duty applications. With up to 150 pounds of clamping pressure, it works great as a quick-action hold-down clamp for jigs or for keeping workpieces in place.Bottom of rubber clamp foot adjusts from level with mounting surface to 7/16" below mounting surface.Total length with arm extended: 2-5/16".Length of arm only extended: 1-1/4"Mounting plate is 1" W x 1-1/16" L.