EZSmart Clamp, Deep

Use the EZSmart Deep Clamp on any of the EZSmart workbenches, tables and guide rails to secure your workpiece for machining. The clamps are designed to be used with all of the different EZSmart extrusions that have channels. In addition to fitting into the channel on the bottom of the guide rails, they can be used with tables such as the EZ-One Woodworking Center (54375, sold separately). Just slide them into the channel on top, underneath, on the side—just about anywhere you wish. Made in USA. Jaw accommodates material up to 4-1/4'' thickNon-marring PVC jaw tips prevent slipping or walking of materialIdeal for use on softer woods or finished surfacesSpring-loaded so the clamp stays open as you position materialApplies even pressure on joints for pocket hole assembly

$16.99
Buy
 

Related Products

Rockler Stainless Steel Pizza Cutter Turning Kit, Pewter Finish

Rockler Stainless Steel Pizza Cutter Turning Kit, Pewter Finish
$19.99

Cut any pizza with ease-a must-have for pizza lovers! Robust, well-balanced hardware is 3X the weight of competing cutters and features a sharp 4'' diameter stainless steel blade. Just add your own custom handle (not included) to top it to your taste. Kit includes a 5/16'' threaded insert that lets you attach the handle or remove it for dishwasher cleaning. A 7/16'' drill bit is required for soft woods or a 1/2'' drill bit for hardwoods. Patent pending. Also available in brass or chrome. See our complete line of turning stock to turn the handle for your pizza cutter. Methods to consider for installing the threaded insert: Use a 5/16'' bolt and double nuts on a drill press. Cut the head off a 5/16'' bolt and chuck it in a drill press. Then thread on two nuts and the insert so that it is flush with the end of the bolt. Tighten the two nuts on the insert so it won't spin on the bolt. After the pilot hole is drilled in the stock, clamp your stock with a handscrew or a drill press vise and manually turn the drill press chuck to drive the insert into the stock. DO NOT TURN ON THE DRILL PRESS. The drill press will keep the insert square to the stock as it is threaded in. We also recommend using beeswax, screw lube, or even soap to lubricate the threads on the insert. This process can also be done on a lathe using a three jaw chuck in the tailstock to manually feed the insert into the stock. Finally, if you're using acrylics for your handle, we have found that heating the insert before installing it makes it go in like a hot knife in butter.

Rockler Thin Rip Tablesaw Jig

Rockler Thin Rip Tablesaw Jig
$26.99

This jig allows you to rip thin strips on the left side of the blade, eliminating the danger of pushing narrow strips between the saw and fence. Since the strip is not trapped between the blade and fence, there is also less risk of binding and kickback. It's simple to use; a single knob locks the jig into the miter track and locks your setting at the same time. Ball bearing guide keeps your workpiece firmly against the fence for perfect repeatability. Use the graduated scale to fine-tune for extremely thin strips. Note: Ripping thin strips requires the use of a zero-clearance insert, sold separately.The perfect tool for edging, inlay, bent laminations and more.Solid phenolic for durability.Low-profile miter track clamp locks in at any point along the miter track.Also works great on the bandsaw as a single-point fence for cutting curved slats in multiples.Adjusts from 1-3/8" away from your miter track to 5-11/16" away from your miter track, enough for the thinnest ripsMeasures 5-1/4"W x 8"L.The jig is stationary, while the fence is moved for each cut.Fits 3/4" W x 3/8" D Miter Tracks

Small T-Handle Clamp

Small T-Handle Clamp
$16.99

Once attached to a bench or fixture, this clamp works great as a quick-action hold down for jigs or as a simple way to secure a work piece. Its holding capacity is approximately 200 pounds.Bottom of rubber foot adjusts from 1/4" above mounting surface to 3/8" below mounting surface. Total length with arm extended and T-handle up is 2-5/8". Height is 2-1/4".Mounting plate is 1-9/16" W x 1" L.Does not include mounting screws.