Sjobergs Duo Workbench with SM03 Cabinet

With four standard vise locations—one on each end, and two along the front edge—the Sjobergs Duo is capable of securely holding nearly any workpiece. Constructed entirely from solid European beech, it also makes no sacrifices in durability. The vises can be rotated to suit left- or right-handed woodworkers. In addition, they can be positioned as dual front vises to hold extra-long boards for jointing, or as dual tail vises for an extended lengthwise clamping capacity of 63''. For strength, the tops are constructed with full-length laminations of knot-free European beech, without any ugly splices. With a thickness of just over 1'' in the center, and a skirt of 2-3/4'', the top is very rigid. The Sjobergs Duo cabinetmaker's workbench is built to provide a lifetime of hard use and enjoyment. Beech top is just over 1'' thick in the middle, and 2-3/4'' around the edgeVises have a 4-1/2'' opening capacityDouble rows of bench dog holes extend from all vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass for less vibrationIncludes four 3/4'' round plastic/glass fiber bench dogs

$1,175.00
Buy
 

Related Products

Rockler Stainless Steel Pizza Cutter Turning Kit, Pewter Finish

Rockler Stainless Steel Pizza Cutter Turning Kit, Pewter Finish
$19.99

Cut any pizza with ease-a must-have for pizza lovers! Robust, well-balanced hardware is 3X the weight of competing cutters and features a sharp 4'' diameter stainless steel blade. Just add your own custom handle (not included) to top it to your taste. Kit includes a 5/16'' threaded insert that lets you attach the handle or remove it for dishwasher cleaning. A 7/16'' drill bit is required for soft woods or a 1/2'' drill bit for hardwoods. Patent pending. Also available in brass or chrome. See our complete line of turning stock to turn the handle for your pizza cutter. Methods to consider for installing the threaded insert: Use a 5/16'' bolt and double nuts on a drill press. Cut the head off a 5/16'' bolt and chuck it in a drill press. Then thread on two nuts and the insert so that it is flush with the end of the bolt. Tighten the two nuts on the insert so it won't spin on the bolt. After the pilot hole is drilled in the stock, clamp your stock with a handscrew or a drill press vise and manually turn the drill press chuck to drive the insert into the stock. DO NOT TURN ON THE DRILL PRESS. The drill press will keep the insert square to the stock as it is threaded in. We also recommend using beeswax, screw lube, or even soap to lubricate the threads on the insert. This process can also be done on a lathe using a three jaw chuck in the tailstock to manually feed the insert into the stock. Finally, if you're using acrylics for your handle, we have found that heating the insert before installing it makes it go in like a hot knife in butter.

Additional Clamp Rods for Pack Rack (Pack of 2)

Additional Clamp Rods for Pack Rack (Pack of 2)
$12.99

Clamp Rods create additional clamp-holding capacity for your Pack Rack Clamp & Tool Storage System (21834 - sold separately).

Auto-Lock T-Track Hold Down Clamp

Auto-Lock T-Track Hold Down Clamp
$29.99

Tightening Rockler's new Auto-Lock T-Track Hold Down Clamp is literally an open-and-shut case-just press down the lever to secure anything from veneer sheets to lumber up to 2-3/4'' thick! Once set, the clamping pressure is always the same regardless of workpiece size, and is adjusted only if needed with the set screw. The clamp pivots 360°, allowing you to clamp near the workpiece edge to minimize obstructions. A large knurled wheel locks the clamp securely to the T-track. The toggle foot is adjusted with the knurled aluminum knob for best placement-no wrenches required-while the clamping foot pivots on a ball joint so it can adapt to any angle and is rubber coated to prevent marring. Simply lift the lever to release. Auto-adjust mechanism allows you to clamp various thicknesses without readjustingCenter of clamping foot extends from 1-1/2'' to 3-1/2'' from center of trackMax height capacity is 2-3/4''Clamping force is adjustable from 5-250 lbs of pressureLarge locking wheel secures clamp to T-trackClamps slide into any T-track that accepts 5/16'' T-bolts, including our T-Track Table (46654, sold separately) and many of the CNC Shark tablesAn optional Mounting Bracket (57940) is available for securing the clamp to shop-made jigs and fixturesHeavy-duty metal construction