The Sjobergs Elite cabinetmaker's workbenches are made in Sweden to the very highest standards. Designed to totally eliminate any vibration, rocking or racking, they are suitable for the most demanding professionals. For maximum strength, the top is constructed with full-length laminations of knot-free European beech, without any ugly splices. Solid beech is also used in the preassembled trestle frames, and the entire bench is treated with top-quality oil. The tops are just under 3-3/8'' thick in the middle, joined with tongue and groove joints for consistent flatness. The skirt around the edge is a sturdy 4-5/16'' in height. The two massive pre-mounted vises, made in Sweden exclusively for Sjobergs, boast a 5-3/4'' opening capacity, and slide along fully adjustable guide rails to eliminate any jaw misalignment. If you are left-handed, the front vise can be moved to the other side of the bench, and the top rotated 180°. The bench also includes four solid steel bench dogs with side springs, while double rows of dog holes permit even the toughest clamping jobs using either vise. The heaviest, most durable benches in the Sjobergs line-built from solid beech and treated with top-quality oilMassive vises are 29'' wide with a 5-3/4'' opening capacityDouble rows of bench dog holes extend from both vise locationsTrestle is also pre-drilled with dog holesIncluded cabinet with doors and drawers offers convenient tool storage and added mass, which further eliminates vibrationIncludes four unbreakable 1'' round steel bench dogs that can be used in both the benchtop and the trestleVises can be rotated for both left- and right-handed useOptional Height Adjustment Blocks (56753, sold separately) raise the working height by 3-1/2'' for taller woodworkers
If you're drilling hinge cup holes for multiple doors of the same height, the JIG IT Deluxe Concealed Hinge Drilling System will save you loads of time. The system comes with a sturdy 36'' aluminum rail and two hinge cup drilling guides that slide along the rail to align with your hinge plates. Once set up, you can use the stop block against the top or bottom of each door to achieve identical results throughout any bank of cabinets. With no need for a drill press, you'll save both money and shop space. Each guide features an integral spring clamp that requires no adjustment, and holds the guide in place as you drill. The clamp also doubles as a foot that rests on your benchtop (or the floor) and provides firm support as you apply downward pressure with the drill bit. To support the outer edge of the door, simply use scrap blocks or Bench Cookies (sold separately). A long shank Forstner bit (sold separately) to match your hinge cup size is required to use the jig. Carbide bits are recommended.For fast and accurate installation of the cabinet plates from two-part Euro-style hinges, check out Rockler's lineup of JIG IT Hinge Plate Templates. Available for many hinges, they make it easy to drill precisely spaced mounting holes in the cabinet.For tall doors requiring three hinges, an additional Concealed Hinge Drilling Guide (58605) can be purchased separately and added to the rail. Includes 3/4'' square aluminum guide rail, and a material stop for precise, repeatable resultsFor very tall doors, simply rip a 3/4'' x 3/4'' stick in whatever length is needed, or purchase a length of standard 3/4'' square aluminum extrusionMakes an ideal hinge cup drilling solution for small shops, or for jobsite workTemplate guides are solid steel for durabilityTemplates are secured in place with sturdy metal threaded holesIntegral clamps attach guides securely to your doorClamps double as feet, providing firm support as you drillUse scrap blocks or Bench Cookies to support outer edgeCenter line perfectly positions the templateOffsets are adjustable for both face frame and frameless constructionTemplate bases have non-marring bottomsDetailed instructions included
Enjoy complete connectivity and a tool-free setup with these sophisticated hose clamps. A unique bridge component steps over coils in right-hand spiraling dust hose, allowing all clamping power to transfer directly to the connection. This hose clamp is Right Hand threaded and is for 2-1/2" clear hose.Features:Superior connection strength.Plastic key requires only finger tightening for powerful clamping force.Longer key shaft gives knuckles clearance when tightening.
Just lay the jig on your stock, tighten the two horizontal tracking knobs and start drilling error-free rows.Guarantees each row is perfectly in lineSpaces each hole exactly 37mm from the edge of your stockJig is easy to set up and easy to adjust for multiple rowsRows are spaced exactly 1-1/4" (32mm) apartPin holes are set back exactly 1-7/16" (37mm) from each edge32mm spacing and 37mm setback are fully compatible with the Euro hinge system24" long twin template tracks are joined by rigid rails that lock in place for error-free drillingDrill two rows with one jig to save time and ensure accuracyLocking 3-star tracking knobs allow for adjustments and ensure the jig stays firmly in placeReversible guide rails have a smooth aluminum surface on one side and a rubber fence on the other for better gripping powerIncludes two 5mm and two 1/4" indexing pins that eliminate the need for clamps and allow you to extend long rows of holes indefinitelyIncluded indexing pins store conveniently in the ends of each guide rail when not in useDrilling template is made of thick acrylic for durabilityDesigned for un-assembled cabinet components from 8-1/4"W to 25-1/4"W Self-Centering Drill Bits:Self-centering bits are pre-set to bore a consistent depth for perfect fitting shelf pins and sleeves every time. No adjustments are necessary! Various bit sizes available separately for both shelf pins and shelf pin sleeves. Decorative metal shelf pin sleeves provided added shelf strength.#40604 - 1/4'' Bit for 1/4'' Shelf Pin#40608 - 5mm Bit for 5mm Shelf Pin#41983 - 9/32'' Bit for 1/4'' Shelf Pin Sleeve#41981 - 7/32'' Bit for 5mm Shelf Pin Sleeve