Eliminate the unsafe distraction of turning on and off your dust collection system while you're operating a shop tool! The iVac Pro consists of two main components, the Pro Switch (Sold Separately) and the Pro Tool, both sold separately in your choice of 240V or 115V. A complete iVac Pro System gives you wireless control of your dust collection system, automatically turning it on/off every time you turn on/off one of your shop tools.Here is how it works: plug your dust collection system into a Pro Switch. Now add a Pro Tool for every shop tool you want to automatically activate your dust collection system. One Pro Switch can accommodate up to 8 Pro Tools, as long as they are within the 40' radio frequency range, making it possible to run your dust collection system only when you run your tools! And running more than one tool at the same time won't cause interference; the Pro Switch won't turn your dust collection system off until the last Pro Tool in your system is shut off. You can even program your Pro Switch to run a little longer than your tool to allow for dust clearance. So get started today by selecting a Pro Switch in 240V or 115V and adding up to 8 Pro Tools.NOTE: IVac Pro System Boxes are built to handle the amperage advertised, however, both the UL (American) and CSA (Canadian) safety approval agencies require the boxes to be labeled at 80% of their actual amperage capacity due to the fact that the units have an attached power supply cord. Example - The 115 Volt / 20 Amp box is labeled as only 16 amps, however the box will actually continuously handle 20 amp AC mains.
The 64B table saw, with left tilt arbor, offers 1-3/4 horsepower in dual voltage to meet the demands of the professional contractor. The transparent blade guard has independent leaves, and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts. An arbor lock is accessed from above the table, eliminating the need for dual blade wrenches. The T-slot miter gauge has rack-and-pinion angle setting, positive stops, and extension plate for expanded workpiece support. The 64B has cast iron table and wings with front edge bevel, and the working area is further expanded by the melamine-surfaced wood extension table. Storage hooks on the stand keep your accessories within reach. Riving knife maintains close blade proximity to reduce chance of kickback Micro-adjust miter gauge with extension plate offers wider crosscut support Blade guard and riving knife have quick release for tool-less mounting and removal Precision ground cast iron table and wings have beveled edge for smooth miter gauge entry Built-in extraction port increases dust collection efficiency Heavy cast iron trunnion ensures smooth blade positioning Chrome trimmed handwheels are ergonomically designed Accu-Fence locks to rail without play (Blade not included) 5 Year Warranty
Thanks to a powerful 1HP motor, ten different spindle assemblies ranging from 1/4'' to 4'' in diameter, plus a full 1-1/2'' of vertical oscillation, the Jet JOSS-S Spindle Sander will make quick work of sanding a huge variety of inside curves. With its heavy-duty floorstanding design and spacious table, even large workpieces can be handled comfortably, with minimal tipping. The table can be tilted up to 45° to the front and 15° to the rear for sanding beveled edges. All spindles conveniently store in a neat rack inside the cabinet. Special attention has been payed to optimizing dust collection on this sander, including a flexible baffle system beneath the table to direct dust into the ports. With its rugged construction and precision ball bearings, this sander is sure to be with you for the long haul. Baffles create a chamber under the table for improved dust collection4'' dust port connects to your dust collection system to keep yourwork area cleanSpindle lock for quick and easy spindle changesTable tilts 45° front and 15° back and features a 90° quick indexIntegrated storage provides designated slots for spindles and table insertsSealed access door minimizes dust in the storage area1-1/2'' oscillating action reduces friction heat to protect wood and prolong sleeve lifeMain spindle support runs on precision ball bearings and is oscillated by a heavy-duty worm and gear mechanism for consistent performanceIntegrated paddle switch with safety keyPowerful 1HP motor is independently mounted inside the base for easy access and serviceIncludes 1/4'', 3/8'', 1/2'', 5/8'', 3/4'', 1'', 1-1/2'', 2'', 3'', and 4'' spindle assembliesSpindles have threaded ends for quick, easy changesWorm and gear mechanism runs in an oil bath to prolong its life and durability
Powermatic 201 Planer, 7.5HP 1PH 230VCast iron 1300 lb. construction for solid performance without vibration2 feed speeds - 20/30 fpm - accommodates rough and fine finish workSegmented infeed roller with sectional chipbreaker allows multiple board planing4-knife head offers 19,200 cuts per minute and widest capacity in its classRoller bearing-mounted feed rollers for long lifeAdjustable bed rollers allow smooth feeding of rough or finished workpiecesOversized cast iron table travels on 2 large lead screws for heavy duty supportStandard Equipment:Dust collection chute with 5" portAdjustable foot padsKnife setting gaugeTool kit (6, 8, and 10mm wrenches, 12-14mm, and 22-24mm combination wrenches)Specifications:Bed Rollers Adjustable from Front:2Brand:PowermaticCuts Per Minute:19,200Cutterhead Diameter (in.):3-1/4Cutterhead Speed (RPM):4800Dust Collection Minimum CFM Required:900Dust Port Diameter (OD/in.):5Feed Rate (FPM):20 and 30Height:59inchInfeed Roller Diameter (in):n.a.Length:42inchMaximum Depth of Cut (in.):3/16Maximum Full Width Depth of Cut (in.):n.a.Maximum Opening (in.):n.a.Maximum Planing Thickness (in.):9-1/4Maximum Planing Width (in.):22Minimum Planing Length (in.):10Model Number:201Motor HP:7-1/2HPMotor Phase:1PhMotor Voltage:230VMovement - Horizontal (in.):n.a.Movement - Vertical (in.):n.a.Movement - Vertical (in.):n.a.Net Weight:1350poundNumber of Knives:4Number of Speeds:twoOutfeed Roller Diameter (in):3Overall Dimensions:42 x 49 x 59Part Number:1791261Planing Thickness Range (in.):n.a.Prewired:n.a.Range of Speeds (FPM):n.a.Readout Scale:mm/inRollers (in.):n.a.Rotation (Forward/Reverse):n.a.Segmented Infeed Roller Diameter (in.):3Ship Weight:1430poundSwing (deg.):n.a.Table Height Adjust Manual:1 Turn = 1/16Table Size (in.):32-1/4 x 24Table Support:2-columnTool Supplied:YesWidth:49inch