Mirka Abranet 5'' Pad Protectors (9955RP), 2-Pack

If you plan to make extensive use of Abranet mesh abrasives, these sanding pad protectors will help to prevent premature wear on your sanding pad. Continuous and aggressive sanding with Abranet can sometimes be hard on sanding pads since dust and debris can migrate freely through the abrasive discs. To remedy this, the protector is positioned between the backing pad and the sanding disc to provide cushioning and protection. Prolongs the life of your sanding padRandomized hole patten fits any 5'' sanderHook-and-loop on one side, Grip on the other-just place between the sanding pad and the abrasive discLow cost and easily replacedHelps to improve dust collection through Abranet mesh

$22.99
Buy
 

Related Products

Jet Combination 6'' x 48'' Belt & 9'' Disc Sander w/Closed Stand

Jet Combination 6'' x 48'' Belt & 9'' Disc Sander w/Closed Stand
$864.99

The unique JSG-96CS Sander combines a 9" disc and 6" x 48" belt for workshop versatility. While small and compact, the JSG-96 offers industrial 3/4 HP power while taking up a small footprint in your shop. A quick-release belt tension lever makes belt changes fast and easy while a quick-lock dust cover allows fast disc changes.Features:Large cast iron table has preset stops at 90° and 45° to let you use the belt sander vertically, horizontally or anywhere in between Exclusive dual thumbscrew belt tracking adjustment locks to keep belt on track during useGraphite covered steel platen runs cooler increasing machine and belt lifeSpecially designed belt guard allows full use of the 6" belt width and lengthDrive drum is rubber-coated for a better grip on the sanding belt resulting in less slippageTracking adjustment knob with quick-lock handle keeps belt on track during useQuick-release belt tension lever makes belt changes fast and easyQuick-lock dust cover allows fast disc changes Single 4" dust port on the back of the base collects dust effectively from both the belt and disc Powerful 3/4HP motor easily handles the toughest sanding operations Built-in handles for easier portability One-piece formed steel heavy-duty closed stand provides additional support and additional storage for abrasives

Powermatic PM1300TX-CK Dust Collector, 1.75HP 1PH 115/230V, 2-Micron Canister Kit

Powermatic PM1300TX-CK Dust Collector, 1.75HP 1PH 115/230V, 2-Micron Canister Kit
$849.99

The PM1300TX Dust Collector features the exclusive TurboCone which improves chip separation to prevent clogging of the filter, and increases packing efficiency of the collector bag. The canister filter offers superior filtering surface area over standard bags, and captures 98% of 2-micron particles. A digital timer can be set for up to 99 minutes, and an infrared sensor allows remote control operation. The all-metal duct improves rigidity and air flow. The clear collector bags are large capacity, which means less down-time changing them. Four swivel casters and conveniently located handles allow for easy mobility. Features:TurboCone improves chip separation and collector bag packing efficiencyThe cone eliminates premature filter clogging for sustained performanceRemote-controlled digital timer can be programmed for up to 99 minutesCanister filter offers over six times filtering surface area of standard bagsAll-metal duct construction for rigidity and improved air flowDual 4" dust ports for simultaneous collection from two machines1-3/4HP motor offers plenty of power for effective air movementCollection bag uses a snap ring for rapid installation and removal10 cubic feet capacity collection bag reduces number of bag changesFour swivel casters for easy maneuverability

Powermatic 6'' Jointer w/Helical Cutterhead

Powermatic 6'' Jointer w/Helical Cutterhead
$1,429.99

This 6" Jointer features a helical cutterhead with 40 four-sided indexable carbide knife inserts - this design provides a superior finish and quieter operation compared to conventional cutterheads, and the inserts require no adjustment once they are installed. If a knife insert becomes nicked, simply rotate it for a fresh edge and continue working. Oversized infeed/outfeed tables are mounted on dovetailed ways. The fence is 38" in length, with positive stops at 90° and 45° right and left. The fine/quick adjustment lever on the infeed table offers quick set-ups with precision controlled depth of cut. The heavy steel stand features a 1 HP motor with a non-slip v-belt drive for maximum performance. The 4" dust port offers easy connection to any dust collection system.Helical cutterhead with four-sided knife inserts provides smoother, quieter cutting and finer finish than conventional systems 66" long adjustable infeed and outfeed tables provide more working surface Fine/quick adjustment lever on infeed table for precision cuts Extra-long 38" two-way tilting fence with positive stops provides quick positioning for 90° or bevel cuts Enlarged sheet metal stand provides a sturdy base 1HP motor offers plenty of power Fence controls are center-mounted for convenience Push button switch is lockable to prevent accidental starting 4" port for dust collection Standard Equipment:1HP TEFC MotorTwo push blocksDust collection portCutterhead guardIndustrial push-button switch