Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table

The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch

$8,629.99
Buy
 

Related Products

Rockwell BladeRunner X2 Portable Tabletop Saw (RK7323)

Rockwell BladeRunner X2 Portable Tabletop Saw (RK7323)
$119.99

The all-new BladeRunner X2 now features a blade guard that is integrated with and supported by the riving knife, minimizing obstructions on the table surface. This means you can rip materials of unlimited width, without running into the blade guard support. As with previous models, the BladeRunner X2 can perform a multitude of cuts including rip cuts, crosscuts, miters and curves. It uses standard T-shank jigsaw blades with tool-free blade changes that take literally seconds to perform. The larger rip fence is now separate from the miter gauge (both are included) for more versatility and stability. The saw sets up in seconds to cut wood, ceramic tile, plastic, mild steel and aluminum. Unlike a jigsaw, the BladeRunner allows you to use both hands to guide the material for maximum control. The dust port lets you connect a vacuum for dust collection. When you're ready to move on to your next job site, just grab the handle in the table top and whisk it away.Features:Cut wood, metal, ceramic tile, aluminum or plastic with one versatile sawIncludes five blades: a general purpose blade for wood, a scrolling blade for wood, a ceramic tile blade, a metal cutting blade and an aluminum cutting bladeWeighs less than 15 lbs-easy to carry anywhereFast, tool-free blade change for nearly instantaneous changeovers between cutting applicationsUses any T-shank jig saw blade measuring 4'' or lessEasy to use-both hands are free to control the workTraditional guard and riving knife system allows unlimited capacity for cross and rip cutsMiter gauge is adjustable for 0° to 60° angled cuts, right or leftOn-board storage for miter gauge and rip fenceSafety switch with key prevents accidental start

iVac Pro 4'' Blast Gate Starter Pack

iVac Pro 4'' Blast Gate Starter Pack
$239.99

This electronically driven automatic blast gate system is an optional upgrade to the iVac Pro Wireless Dust Collection Control System, bringing one-touch simplicity to managing your dust collection airflow. Simply turn on your power tool, and the iVac Pro Tool (42891, sold separately) sends a wireless signal to automatically open the corresponding Pro Blast Gate, and another signal to the iVac Pro Switch (42897, sold separately), which turns on your dust collector. Turn off your power tool, and after a short interval to clear dust, the blast gate closes and the dust collector powers down. This automation prevents the irritating dust clouds that result from forgetting to open a blast gate, and the reduced suction that results from forgetting to close it afterward. The system also ensures that at least one gate stays open when the vacuum is on to prevent overloading the motor on your dust collector. Prevents the irritating dust clouds you get from forgetting to open the blast gateReduces the potential for accidents from reaching for blast gates while machines are runningOptimizes the suction in your system by keeping a minimum number of gates open at one timeBlast gates can also be controlled via the handheld wireless remote or manually with the toggle switchKit includes two blast gates for 4'' hose, two 115v AC adapters, a wireless remote control and a manual toggle switchUp to eight blast gates can operate on one systemAdditional blast gates available separately (52504)RF range: 40'

iVac Pro Switch Wireless Dust Collection Controller System

iVac Pro Switch Wireless Dust Collection Controller System
$69.99

Eliminate the unsafe distraction of turning on and off your dust collection system while you're operating a shop tool! The iVac Pro consists of two main components, the Pro Switch and the Pro Tool (Sold Separately), in your choice of 240V or 115V. A complete iVac Pro System gives you wireless control of your dust collection system, automatically turning it on/off every time you turn on/off one of your shop tools. Here is how it works: plug your dust collection system into a Pro Switch. Now add a Pro Tool for every shop tool you want to automatically activate your dust collection system. One Pro Switch can accommodate up to 8 Pro Tools, as long as they are within the 40' radio frequency range, making it possible to run your dust collection system only when you run your tools! And running more than one tool at the same time won't cause interference; the Pro Switch won't turn your dust collection system off until the last Pro Tool in your system is shut off. You can even program your Pro Switch to run a little longer than your tool to allow for dust clearance. So get started today by selecting a Pro Switch in 240V or 115V and adding up to 8 Pro Tools.NOTE: IVac Pro System Boxes are built to handle the amperage advertised, however, both the UL (American) and CSA (Canadian) safety approval agencies require the boxes to be labeled at 80% of their actual amperage capacity due to the fact that the units have an attached power supply cord. Example - The 115 Volt / 20 Amp box is labeled as only 16 amps, however the box will actually continuously handle 20 amp AC mains.