Rockler 2-1/2'' StableGate with Bracket

Unsecured blast gates can be sloppy and tedious to operate. Opening the gate often pulls the hose away from the wall. With its built-in mounting element, the StableGate™ takes care of everything. Just anchor it directly to the wall for clean and stable operation.

$5.99
Buy
 

Related Products

Powermatic PM1300TX-CK Dust Collector, 1.75HP 1PH 115/230V, 2-Micron Canister Kit

Powermatic PM1300TX-CK Dust Collector, 1.75HP 1PH 115/230V, 2-Micron Canister Kit
$849.99

The PM1300TX Dust Collector features the exclusive TurboCone which improves chip separation to prevent clogging of the filter, and increases packing efficiency of the collector bag. The canister filter offers superior filtering surface area over standard bags, and captures 98% of 2-micron particles. A digital timer can be set for up to 99 minutes, and an infrared sensor allows remote control operation. The all-metal duct improves rigidity and air flow. The clear collector bags are large capacity, which means less down-time changing them. Four swivel casters and conveniently located handles allow for easy mobility. Features:TurboCone improves chip separation and collector bag packing efficiencyThe cone eliminates premature filter clogging for sustained performanceRemote-controlled digital timer can be programmed for up to 99 minutesCanister filter offers over six times filtering surface area of standard bagsAll-metal duct construction for rigidity and improved air flowDual 4" dust ports for simultaneous collection from two machines1-3/4HP motor offers plenty of power for effective air movementCollection bag uses a snap ring for rapid installation and removal10 cubic feet capacity collection bag reduces number of bag changesFour swivel casters for easy maneuverability

5'' to 4'' Adaptor

5'' to 4'' Adaptor
$6.99

Dust collection adaptors are ideal for connecting two different size hoses together. If used properly, the result can produce increased air velocity near your dust collector where it's needed most!Large End: 4-7/8" OD - 4-5/8" IDSmall End: 3-15/16" OD - 3-5/8" ID

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table
$8,629.99

The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch