The 6012 Series by Rev-a-Shelf is a two shelf Full Circle System with dependently rotating shelves, available in 24" diameter. These polymer full circle sets feature a ¾" zinc diameter shaft system for absolute durability and a telescoping shaft accommodating heights from 26"-32". Shelves are available in white or almond color.Polymer 2-Shelf Set with telescoping shaftAccommodates 26"-32" inner cabinet heightsDependently rotating hardwareLimited Lifetime WarrantyTechnical DetailsAvailable in 24" diameterAvailable in White or AlmondDependently rotating shelvesFeatures 3/4" zinc diameter shaft system for absolute durabilityThe 6012 (2 shelves)units feature a telescoping shaft accommodating heights from 24" - 31"Made of durable polymer6000 SERIES FULL CIRCLE REV-A-SHELF SYSTEMWITH TELESCOPING PIVOT HARDWARE Locate the bottom pivot by placing one of the shelves on the base of the cabinet and marking through the center hole making sure the shelf will have at least 3/8 in. side clearance all around. Pilot drill (1/8 in. dia.) holes and fasten the bottom pivot with four (4)1/2" x #8 truss head wood screws. Slide the collar assembly over the center shaft and start the screw into the hole in the center shaft. Insert the upper shaft assembly all the way into the center shaft. Set the shaft assembly on the bottom pivot and extend the upper shaft to the top of the cabinet. Plumb with level to locate the center for the top pivot bracket. Pilot drill (1/8" in. dia.) holes and fasten the top pivot with four (4) 1/2 in. x #8 truss head wood screws. You are now ready to assemble the unit inside the cabinet. Place the shelves inside the cabinet over the bottom pivot bracket and slide the shaft assembly through the shelves. Lift the shaft assembly and engage it in the bottom pivot, whie holding the shelves up with one hand. Extend the upper shaft assembly and engage it in the top pivot bracket and tighten the locking screw on the collar assembly securely. Adjust the shelves to the desired heights and tighten the shelf locking screws securely. NOTE: A little lubricant (white grease or equivalent) applied to the top and bottom pivot will insure quiet and smooth turning.
Special T-nuts for use with the Riveting T-Nut Insertion Tool (30167, sold separately) in 1/2" thick material. The tool folds over the end of the T-nut, creating a neat, clean mushroomed end that holds the T-nut firmly in place. T-nut internal thread size: 1/4"-20. Package of 10.
Top-quality 2" pin nails for the Grex P650 23-guage Headless Pin Nailer (30918, sold separately). Pack of 2,500.All Grex 23-gauge pins are manufactured and tested to ensure accurate dimensional specifications, optimal material composition and dependable collation of pin strips.Caution: Loading fasteners incorrectly will damage your equipment!
Whether you're organizing loose hardware or trying to identify the thread pitch so you can purchase replacements, the Thread Detective is the perfect tool for the job. Available in standard or metric, each set features clearly marked gauges for quick identification of the size and thread pitch of both nuts and bolts. One end of each gauge checks the nuts, while bolts can be threaded into the other end. The gauges are strung together onto a wire lanyard that can be hung from a nail for convenient storage. Jumbo imperial gauges are red, and include 6 thread checkers. Jumbo metric gauges are blue and include 8 thread checkers. For smaller thread gauges, see the original Thread Detectives: (50751 and 53816, sold separately). Standard (red) Jumbo Thread Detectives include nut and bolt sizes of: 5/8-11, 5/8-18, 3/4-10, 3/4-16, 1-8 and 1-12. Metric (blue) Jumbo Thread Detectives include nut and bolt sizes of M14 x 1.5, M14 x 2.0, M16 x 1.5, M16 x 2.0, M20 x 1.5, M20 x 2.5, M24 x 2.0 and M24 x 3.0.