This optional sprayer needle fits the Apollo E5011 bleeder-style spray gun, which is included in many of our Apollo ECO HVLP turbine packages (e.g. 50810, sold separately). It's a 2.0mm needle as opposed to the 1.0mm needle that comes standard on the E5011.
The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch
This traditional round rail comes in a dark oil-rubbed bronze finish, allowing you to match it seamlessly with other Hafele closet accessories. Aluminum construction is sturdy and lightweight. Each rail includes two metal supports, which interface with the 32mm hole-drilling system. Choose from five pre-cut lengths, or buy longer lengths and cut them down to size. Available in Dark Oil-Rubbed Bronze finish. 1-5/16" diameter.
Powermatic 201 Planer, 7.5HP 1PH 230VCast iron 1300 lb. construction for solid performance without vibration2 feed speeds - 20/30 fpm - accommodates rough and fine finish workSegmented infeed roller with sectional chipbreaker allows multiple board planing4-knife head offers 19,200 cuts per minute and widest capacity in its classRoller bearing-mounted feed rollers for long lifeAdjustable bed rollers allow smooth feeding of rough or finished workpiecesOversized cast iron table travels on 2 large lead screws for heavy duty supportStandard Equipment:Dust collection chute with 5" portAdjustable foot padsKnife setting gaugeTool kit (6, 8, and 10mm wrenches, 12-14mm, and 22-24mm combination wrenches)Specifications:Bed Rollers Adjustable from Front:2Brand:PowermaticCuts Per Minute:19,200Cutterhead Diameter (in.):3-1/4Cutterhead Speed (RPM):4800Dust Collection Minimum CFM Required:900Dust Port Diameter (OD/in.):5Feed Rate (FPM):20 and 30Height:59inchInfeed Roller Diameter (in):n.a.Length:42inchMaximum Depth of Cut (in.):3/16Maximum Full Width Depth of Cut (in.):n.a.Maximum Opening (in.):n.a.Maximum Planing Thickness (in.):9-1/4Maximum Planing Width (in.):22Minimum Planing Length (in.):10Model Number:201Motor HP:7-1/2HPMotor Phase:1PhMotor Voltage:230VMovement - Horizontal (in.):n.a.Movement - Vertical (in.):n.a.Movement - Vertical (in.):n.a.Net Weight:1350poundNumber of Knives:4Number of Speeds:twoOutfeed Roller Diameter (in):3Overall Dimensions:42 x 49 x 59Part Number:1791261Planing Thickness Range (in.):n.a.Prewired:n.a.Range of Speeds (FPM):n.a.Readout Scale:mm/inRollers (in.):n.a.Rotation (Forward/Reverse):n.a.Segmented Infeed Roller Diameter (in.):3Ship Weight:1430poundSwing (deg.):n.a.Table Height Adjust Manual:1 Turn = 1/16Table Size (in.):32-1/4 x 24Table Support:2-columnTool Supplied:YesWidth:49inch