2-1/2" x 11" Birch Embossed Carving

These quality carvings come ready to finish. Birch carving measures 2-1/2" High x 11" Wide.

$9.99
Buy
 

Related Products

Gel Stain - General Finishes - Antique Walnut

Gel Stain - General Finishes - Antique Walnut
$9.99

The foolproof finishing system! Just wipe on with a clean cloth and you're ensured of professional quality results without brush marks. Stains dry to the touch in minutes. If you want a darker color, apply another coat of stain in only 6 hours. Once you're satisfied with the color, apply General Finishes's satin gel topcoat finish. Special formula repels dust between coats. No sanding needed between coats and no unpleasant smell.Note:Coded as a flammable substance by the U.S. Department of Transportation. Can not be shipped by air or through the postal systemHow To Apply the Oil Base Gel StainApplying the gel stain is a simpler process than traditional stains that require sanding between coats. Before you apply your stain however you should prep your piece to ensure the stain covers correctly. Clean the surface you plan to stain Sand the surface. The suggested grit is 120-150 grit, you want to make sure that any existing finish that might be peeling is removed so the stain applies to the actual project surface. Apply the gel stain liberally with either a cotton cloth, natural bristle brush or a poly foam brush. (Be sure to test a small area of your project to make sure it is the finish you want and that the application method you've chosen is working well for you.) Wipe off the gel stain going with the grain using a clean dry cotton cloth or high quality paper towels. Let it dry, between coats give you project a chance to dry. Drying time varies based on the size and nature of your project as well as the environment it's located in. Normally drying time ranges from 6 to 12 hours. Repeat Steps 3-5 IF you want more coverage or you want a deeper/richer finish.Suggested TopcoatTopcoat can be used as a sealer over paints and stains or as a clean finish. If you want to use a top coat the recommended topcoat is Oil Based Arm-R-Seal Urethane Topcoat (sold separately).

Combination Waterstones

Combination Waterstones
$26.99

Keep your valuable tools in peak condition!Combination Waterstones: For preliminary sharpening where chips exist or bevel angle need to be changed, use the 250/100 waterstone. To remove smaller nicks and do a finish sharpening of woodworking chisels and other tools, the 800/4000 combination is the best choice. Finally, use the 1000/6000 waterstone for creating a polished edge. As shown in the photo on the left.Extremely tough man made abrasive material. These stones cut faster than oilstones. Stones must be soaked in water prior to use and kept wet with water during use. Waterstones develop a slurry to speed the honing process.20549 - 250/1000 Combination Grit Waterstone: 7-1/4" (L) x 1" (thick) x 2-1/4" (W)20542 - 800/4000 Combination Grit Waterstone: 7-1/4" (L) x 1" (thick) x 2-1/4" (W)47506 - 1000/6000 Combination Grit Waterstone: 8-1/8" (L) x 1" (thick) x 2-1/16" (W)47522 - Nagura Stone: 3" (L) x 1" (thick) x 7/8" (W)Nagura Stone: Forms a paste on finer grit Waterstones to speed and enhance polishing. Use with the 6000 grit stone. These stones can be reflattened after sharpening wears the surface by wet sanding the stone on a flat surface with silicone carbide wet - dry abrasive sheet.Waterstone Holder: For non-slip sharpening. The arms are made from chrome plated steel that resists rusting. Holder handles stones 7 to 9" long.

Top Knobs Knob, M608

Top Knobs Knob, M608
$10.49

* Every piece is hand-finished, hand-polished, and then prior to packaging, every piece is hand-inspected for quality.* Top Knobs products are not just metal, they are a higher grade metal as well - high-grade brass, cast bronze, steel, and zinc alloy for long life, minimal wear, and best finishes.* Our beauty is not just skin deep - you can feel the Top Knobs difference in the weight of our products simply by holding products in your hands.Finish: Patine BlackBase Material: SteelWidth: 1-1/8"Projection: 1-5/16"Knob Diameter: 1-1/8"Screws are includedScrew Weight: 0.21Screw Size: M4 Screw PackWarranty: Limited Lifetime