Tone your finishes and blend spot repairs seamlessly with fine-touch spray action! This line of Behlen Master Toners contains a unique combination of nitrocellulose lacquer and fade resistant dyes that will shade your finish without loss of clarity. Master Toner can also be used prior to applying a topcoat to provide uniform wood stain clarity. 13 fl. oz.May be topcoated with nitrocellulose lacquer.Spray thin coats until desired opacity is achieved.Allow final coat at least 2 hours dry time before application of top coat.Can only be shipped by UPS Ground to addresses within the continental United States.
The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch
T-Molding can produce a professional and finished feel on a project while allowing you to protect edges of your project. This style of edge banding can be found on desks and tables where it can help protect furniture from the wear and tear that bumping into it can cause. Our Plastic T-Molding is flexible and can be used to add bit of flare in addition to protection, try choosing from our selection of colors to create either a strong contrast with the finish of the furniture or a complementary one. Plastic T-Molding edging is available in tan, brown, black and white.
Finish: Gilded BronzeBase Material: ZincLength: 4 1/3 inchWidth: 3/5 inchProjection: 1 3/7 inchCenter to Center Hole Spacing: 3 3/4 inchMachine Screw Thread Size: 2 x #8 32 x 1 inchScrews are includedWarranty: Lifetime