Spraying water and oil-based coatings is so much easier and convenient with the Earlex Spray Station 5500-and you get a quality spray-on finish! This semi-pro paint spray station is designed for the light contractor, woodworker, and serious DIY enthusiast. It has three spray patterns with an adjustable 1'' to 12'' fan width, a one-quart container, 13' hose that allows you to reach around large projects, and comes with a general purpose 2.0mm stainless steel needle for most paints, and a 1.5mm needle for varnish, water-based stains, lacquers, and shellac. Now you can achieve showroom-quality finishes on cabinets, furniture, interior and exterior doors, shutters, even cars. Three spray patterns; two for flat surfaces, one for detailed work like spindles or rough surfacesFast Push N' Click pattern switchAdjustable 1" to 12" fan widthPro-Metal Spray Gun with one-quart teflon coated container for fast, easy cleanupBuilt-in spray gun storage area prevents the container from tipping when not in useBuilt-in carry handle makes mobility easy13' paint hose and 13' power cord give you mobility to get the job done fast
A long time favorite for its rich color and excellent workability, Cherry continues to gain popularity for use in fine furniture and cabinets. The wood leaves the sawmill with a pinkish, rosy tone, and continues to darken over years to a deep, lustrous red. The narrow sapwood has a creamy color, similar to Hard Maple. Cherry is easily worked with hand tools and takes an excellent finish and polish. All boards are machined S4S, and are planed to 1/8", 1/4", 1/2" and 3/4" thicknesses, relieving your planer of excess work. Thin boards are well-suited for edging, veneering, marquetry, sides for decorative boxes, bending stock and bent laminations, while the thicker boards are ideal for furniture, paneling, cabinet doors, mouldings, drawer sides, fine jewelry boxes and whatever else your imagination can dream up!Distribution: As many as five varieties of Black cherry are reported to thrive throughout North America.Tree: Attains heights of about 100 feet (30 m) Average tree grows to about 80 feet (24 m) in height, and produces a tall trunk, about 24 inches (60 cm) in diameter. Cherry trees are usually large enough to harvest after 35 to 40 years. Full height is attained in about 100 years.Light & Air-Induced Changes: Black cherry is very sensitive to UV light, which causes it to darken over time. UV light inhibitors in coatings can be used to prevent color change.Grain: Fine grain. Material with dark wavy streaks are frequent. Quartersawn lumber has a shimmery appearance.Texture: Fine and uniform. The wood often has narrow brown pith flecks and small gum pockets.Luster: Rich and satiny. Odor: Emits a fruity aroma when cut.Steam Bending: Good. Often compared to Beech and Ash.
Each sheet of our Baltic Birch Plywood features exceptional strength and the ability to be finished to meet your project needs. The front, back and inner plies are all quality one-piece sheets, which result in excellent screw holding power. Faces may contain some matched plugs, and one face is light and even in color for an attractive finished face. All pieces are 30'' long, and are ripped to 12'' wide for bookcases, shelving and more narrow cabinets. Available in thicknesses of: 1/8'', 1/4'', 1/2'' and 3/4''. All dimensions are nominal and may be slightly undersized. Grade BB/BB: Both faces are relatively "void free" but may contain small patches and a slight knot pattern or mineral streaks. One face is light and even in color. Open knots and defects in a BB face veneer have been removed and replaced with small uniform ''football'' patches before being glued. The end result is a strong plywood that is attractive enough to be used on a variety of projects. 1/8'' thick Baltic Birch contains 3 plies1/4'' thick Baltic Birch contains 5 plies1/2'' thick Baltic Birch contains 9 plies3/4'' thick Baltic Birch contains 13 plies
These Driver Connection Cables are compatible with the Hafele Loox 2013/2015 LED Ribbon Lights (e.g. 48238, sold separately). Use them to connect additional lights to the driver, or to connect cutoffs from your roll of ribbon lights.