Paint Grade Tulip Bun Foot

Ready to sand lightly, paint and install on sofas, easy chairs, beds, desks and shelves. Each 4-5/8" High x 3-1/2" Diameter bun foot includes pre-installed 5/16'' - 18 hanger bolt.

$19.99
Buy
 

Related Products

Corner Mortising Chisel

Corner Mortising Chisel
$14.99

This easy to use spring loaded chisel instantly squares round corners on hinge mortises. Made of hardened steel that stays sharp. Just tap lightly with a hammer for a perfectly squared corner.

Poplar Large Country French Bun Foot

Poplar Large Country French Bun Foot
$14.99

Ready to sand lightly, paint and install on sofas, easy chairs, beds, desks and shelves.

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table

Powermatic TS29 Shaper, 7-1/2HP 3PH 230/460V with Sliding Table
$8,629.99

The new TS29 Tilt/Slide Shaper is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, accurate set-ups. The full guard includes two stock hold-downs and a see-through cover that flips up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish. An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble-free performance. Powered by a big 7-1/2HP motor that drives the spindle forward and reverse with five speeds. The massive sliding table is fully supported by six tapered precision bearings through a full four-foot stroke. In addition, on board the table is a large miter head complete with stock hold-down clamp and a 56" miter fence with flip stop. The large table can easily accommodate a stock feeder for longer production runs.Sliding table with 4-foot stroke works with miter head, hold-down and fence to accomodate everything from multiple end cuts to tenonsFully adjustable fence with dual digital readout for fast, accurate set-up and repeatabilityLarge table with built-in slider with room for stock feeder7" vertical spindle travel allows stacked toolingSpindle tilts negative 5 degrees to positive 45 degrees for increased versatilityLarge diameter multiple table inserts accomodate virtually any size cutterFive spindle speeds in forward and reverse with lighted indicatorSpecifications:Brand:PowermaticDust Collection Minimum CFM Required:800Dust Port Diameter (OD/in.):5 (dual ports)Electrical Controls - Magnetic Starter:24V MagneticFence Size (L x H/in.):46 x 5Fence Travel (Major and Minor/in.):5-3/8 and 3-5/8Height:53inchLength:51inchMaximum Diameter Cutter Above Table (in.):12Maximum Diameter Cutter Below Table (in.):9Model Number:TS29Motor HP:7-1/2HPMotor Phase:3PHMotor Voltage:230/460VNet Weight:1100poundOverall Dimensions:51 x 44 x 53Part Number:1791284Prewired:Prewired 230VReversable:YesRouter Bit Collet Diameter (in.):1/4 and 1/2Ship Weight:1280poundSlide Table Size (in.):11-1/4 x 51-1/4Spindle Diameter (in.):3/4, 1, and 1-1/4Spindle Size Under Nut (in.):3/4 Spindle - 3-1/2, 1 Spindle - 6-1/4, 1-1/4 Spindle - 6-1/4Spindle Speed (RPM):3000, 4000, 6000, 8000, and 10,000Spindle Travel (in.):7Table Inserts:one tilting, two straightTable Size (in.):51-1/2 x 33-1/2Table T-Slot (in.):n.a.Table Travel (in.):49-1/4Tilting Spindle (deg.):5 degrees back, 45 degrees forwardWidth:44inch