Powermatic 201 Planer, 7.5HP 1PH 230VCast iron 1300 lb. construction for solid performance without vibration2 feed speeds - 20/30 fpm - accommodates rough and fine finish workSegmented infeed roller with sectional chipbreaker allows multiple board planing4-knife head offers 19,200 cuts per minute and widest capacity in its classRoller bearing-mounted feed rollers for long lifeAdjustable bed rollers allow smooth feeding of rough or finished workpiecesOversized cast iron table travels on 2 large lead screws for heavy duty supportStandard Equipment:Dust collection chute with 5" portAdjustable foot padsKnife setting gaugeTool kit (6, 8, and 10mm wrenches, 12-14mm, and 22-24mm combination wrenches)Specifications:Bed Rollers Adjustable from Front:2Brand:PowermaticCuts Per Minute:19,200Cutterhead Diameter (in.):3-1/4Cutterhead Speed (RPM):4800Dust Collection Minimum CFM Required:900Dust Port Diameter (OD/in.):5Feed Rate (FPM):20 and 30Height:59inchInfeed Roller Diameter (in):n.a.Length:42inchMaximum Depth of Cut (in.):3/16Maximum Full Width Depth of Cut (in.):n.a.Maximum Opening (in.):n.a.Maximum Planing Thickness (in.):9-1/4Maximum Planing Width (in.):22Minimum Planing Length (in.):10Model Number:201Motor HP:7-1/2HPMotor Phase:1PhMotor Voltage:230VMovement - Horizontal (in.):n.a.Movement - Vertical (in.):n.a.Movement - Vertical (in.):n.a.Net Weight:1350poundNumber of Knives:4Number of Speeds:twoOutfeed Roller Diameter (in):3Overall Dimensions:42 x 49 x 59Part Number:1791261Planing Thickness Range (in.):n.a.Prewired:n.a.Range of Speeds (FPM):n.a.Readout Scale:mm/inRollers (in.):n.a.Rotation (Forward/Reverse):n.a.Segmented Infeed Roller Diameter (in.):3Ship Weight:1430poundSwing (deg.):n.a.Table Height Adjust Manual:1 Turn = 1/16Table Size (in.):32-1/4 x 24Table Support:2-columnTool Supplied:YesWidth:49inch
If exposed to the open air for long periods of time, the cast iron surfaces of your table saw will inevitably begin to rust. Not with the Zerust Table Saw Cover, however. Once installed, this proprietary cover emits non-toxic vapor corrosion inhibitors (VCIs) that surround your table saw to prevent rust, corrosion and electrochemical reactions. Of course, it also helps to shield your equipment from airborne moisture, dust and abrasions. The rust and corrosion inhibitors will remain active for 5 years after the date of purchase. Made in USA. Dimensions: 45''W x 63''L x 19''HRemains effective for five yearsCleaner and more convenient than oilAlso great for other power tools such as lathes, jointers, planers and more
A long time favorite for its rich color and excellent workability, Cherry continues to gain popularity for use in fine furniture and cabinets. The wood leaves the sawmill with a pinkish, rosy tone, and continues to darken over years to a deep, lustrous red. The narrow sapwood has a creamy color, similar to Hard Maple. Cherry is easily worked with hand tools and takes an excellent finish and polish. All boards are machined S4S, and are planed to 1/8", 1/4", 1/2" and 3/4" thicknesses, relieving your planer of excess work. Thin boards are well-suited for edging, veneering, marquetry, sides for decorative boxes, bending stock and bent laminations, while the thicker boards are ideal for furniture, paneling, cabinet doors, mouldings, drawer sides, fine jewelry boxes and whatever else your imagination can dream up!Distribution: As many as five varieties of Black cherry are reported to thrive throughout North America.Tree: Attains heights of about 100 feet (30 m) Average tree grows to about 80 feet (24 m) in height, and produces a tall trunk, about 24 inches (60 cm) in diameter. Cherry trees are usually large enough to harvest after 35 to 40 years. Full height is attained in about 100 years.Light & Air-Induced Changes: Black cherry is very sensitive to UV light, which causes it to darken over time. UV light inhibitors in coatings can be used to prevent color change.Grain: Fine grain. Material with dark wavy streaks are frequent. Quartersawn lumber has a shimmery appearance.Texture: Fine and uniform. The wood often has narrow brown pith flecks and small gum pockets.Luster: Rich and satiny. Odor: Emits a fruity aroma when cut.Steam Bending: Good. Often compared to Beech and Ash.
The distinctive striped appearance of Zebrawood has made it a favorite for decorative inlays and veneers. The color ranges from golden-yellow to a peanut butter tone with chocolate veins running through it. The wood is hard, dense and extremely tough. These thin boards are machined S4S to 1/8" and 1/4" thicknesses, eliminating wear and tear on your planer. You won't have to worry about tearout, which is difficult to prevent when planing thin stock. Thin boards are ideal for edging, veneering, inlay, marquetry, sides for decorative boxes, bending stock, bent laminations and whatever else your imagination can dream up!Native to: West Africa, especially Gabon and Cameroon.Tree Data: 48" to 60" diameter trunk. The trees generally have very thick bark.Sapwood: Pale yellow.Heartwood: Light golden-yellow or pale yellow-brown, with narrow streaks of dark brown to almost black, giving a striped appearance.Grain: Generally interlocked or wavy, yielding a ribbon figure. Texture: Medium to coarse. Luster: High luster.Resin: Occasional resin pockets.Movement: Dimensionally stable. Retains its shape well after machining.Veneering Qualities: Zebrawood is used extensively in veneers for cross banding and inlays. Bundles of veneer should be stabilized with weights to prevent buckling.Working characteristics: Responds well to hand and machine tools. Quite easy to saw, but due to interlocking grain, planing is very difficult, often resulting in tearout.Polishing: Good polishing and finishing qualities. Strength: Compressive strength parallel to the grain is high. The wood is hard, very heavy, and very dense. It is tough, with good impact resistance.