Our Pro Phenolic Router Tables feature one-piece 3/4'' solid phenolic construction for an ultra-flat, low-friction surface that won't warp, dent, scratch or delaminate. The whiter, brighter finish enhances visibility, while our CNC-machined aluminum router plates offer better precision and repeatability than ever before. 3/4'' T-profile miter slot allows you to use precision aftermarket miter gauges, while universal T-tracks in both the fence and table accept stops, hold-downs and more. Included aluminum Pro Fence features two adjustable white melamine MDF faces, front- and rear-facing accessory T-tracks, a dust port and a bit guard. Choose from four pre-drilled plates for common router bases, or two non-drilled plates. Either way, you'll get a perfect fit with far fewer catch points than typical ''Swiss Cheese'' universal plates. Aluminum router plate is CNC machined for incredible flatness and precisionSteel stand has adjustable feet for stability on uneven floors, and pre-drilled holes for adding a shelf and sides24'' x 32'' table for over five square feet of surface area8-point plate leveling system with two locking pointsErgonomic T-knobs for easy fence adjustmentIncludes Rockler Pro Fence with extruded aluminum backer for straight, accurate cutsOpening in fence is easily adjustable to accommodate large router bitsFence backer features top-mounted universal T-track that accepts 5/16'' T-bolts, 1/4'' T-bolts, and 1/4'' hex boltsIncludes dust port and bit safety guard for safe routingFence features a 2-1/2" O.D. (2-1/4" I.D.) dust port 53395 - Rockler Pro Phenolic Router Table, Pro Fence, Stand and Non-Drilled Plate with 3-1/4'' Opening (for Standard Inserts) 59034 - Rockler Pro Phenolic Router Table, Pro Fence, Stand and Non-Drilled Plate with 3-11/16'' Opening (for Large Inserts) To choose a pre-drilled plate, find your router below. If it's not listed, choose from two non-drilled plates-one with a 4'' insert ring, and the other a 4-3/8'' insert ring-and drill the plate to fit your router. Plate A routers: Makita 1100; Milwaukee 5615-5624; DeWalt 616-618; Bosch MRC23 Series, 1617-1618; Ridgid 2930 Combo Kit; Hitachi M12VC (fixed and kit); Porter-Cable 690, 890, 7529, 97529 and 8529. Note: Current models of the Porter-Cable 892 require at least two screws to be 1/2" long versus 5/8".Plate B routers: DeWalt DW621 and DW621K; Craftsman Standard; Freud FT 1700E and 1702VCEKPlate C routers: Porter-Cable 7518, 7519, 7538 and 7539; Milwaukee 5625-20; Triton TRA001 and MOF001Plate D routers: Bosch 1619-1619EV; Freud FT2000; DeWalt 625
The Grr-Ripper Gravity Heel Kit provides a positive hook that grips the end of your board, ideal when you need additional support for feeding hard or heavy stock through your table saw, bandsaw or router table. The heel drops down automatically, aided only by gravity, and retracts when placed in the middle of the board. This means there's no need to remove it or adjust it when it's not needed. The Gravity Heel can also be adjusted laterally to provide backup support when you wish to prevent grain blowout of any kind. Simply saw through the heel to provide zero-clearance support. Five sacrificial heels are included, plus two heel spacers and mounting hardware. Fully adjustable for stock thicknesses from 0-1''Fits all existing Grr-Ripper push blocksEasy to use with two push blocks and the leapfrog method; heels grab the tail end of your board and automatically retract mid-boardIncreases control and stability when feeding long or short stock-provides extra support to help feed stock and prevent blow out
These heavy-duty, state-of-the-craft cutters produce perfect tenons with 60° tapered shoulders for the sturdiest-possible log furniture construction. The funnel shaped, self-centering design ensures flawlessly shaped tenons, and dual precision-ground blades cut twice as fast as single blade models and stay sharp longer. Plus, as part of the cutters' exclusive "IN-SIGHT" visual measurement system, slots along the shaft combine with radial grooves at 1/2" intervals to let you to see your progress and measure tenon length while you cut. Body is CNC machined from aircraft aluminum for maximum strength and minimum weight. Available in three sizes (1", 1-1/2", and 2") corresponding to the diameter tenon that each will cut.
The CNC Shark Touch Probe attaches to the router in any CNC Shark Routing System to trace objects down to 0.001" detail allowing the user to import image data for replicating objects, shapes and patterns. Simply program the Shark to operate at the same detail level as the Touch Probe scan to reproduce the object later. Works well for replicating basic shapes for carvings or reproducing damaged areas on antiques or other irreplaceable items. Requires Cut 3D Software or similar software to be used with the CNC Shark models. Made in the USA. NOTE: To avoid accidents or injury, always be sure to unplug the router prior to attaching the Touch Probe. Touch Probe is compatible with the following machines: CNC Shark Routing System CNC Shark Pro Plus Routing System CNC Shark HD 2.0 Routing System The probe does not work with the 54111 CNC PiranhaIntroducing CNCSharkTalk.com, a new website presented by Rockler where CNC Shark users can chat together, watch how-to videos, ask questions, learn from each other and even show off their CNC Shark projects.