Micro Jig GRR-Ripper Advanced 3D Push Block System GR-200

This advanced model of the GRR-Ripper boasts all of the same innovative features of the GR-100 but comes with two additional accessories (see below) that improve the control and expandability of the GRR-Ripper System. The Micro Jig GRR-Ripper Advanced 3D Pushblock (GR-200) is designed to feed your workpiece more safely and more accurately than with conventional push blocks, resulting in intact fingers, less burning and less waste. With its 3-Directional control, it gives you downward, forward, and lateral pressure on the stock for maximum control. Since it acts as a movable blade guard that travels with your hand, it provides an additional safety buffer between the blade and your hands. Whether you are making razor-thin veneer strips, building miniatures, or creating exquisite furniture you will save time, materials, and fingers with the GRR-Ripper.The GR-200 includes these additional accessories:The Adjustable Spacer - This accessory adds increased gripping surface for tackling larger stock. It also adds one inch of cutting width to the GRR-Ripper and acts as a secondary balance support for small stock and straight-line ripping. Great add-on for working on the router table, and eliminating snipe.The Stabilizing Plate - The Stabilizing Plate adds a new dimension of control to the GRR-Ripper. It is particularly useful when cutting small narrow pieces of stock. Perfect for trickier cuts like resawing, bevel edging, pattern routing, and much more.The Stabilizing Plate also acts as a secondary fence that travels with the GRR-Ripper along the left side of the stock. It holds the off-cut piece in its original position through the entire cutting operation. Some users call it a "Feather Board Plate," but unlike a featherboard, it exerts no sideways pressure. Instead it simply holds the drop-off piece in position as it travels past the blade, preventing binding.Watch a video demo today by clicking on the "Videos" tab above.

$79.99
Buy
 

Related Products

''C'' Series All In One Contractor Router Plate

''C'' Series All In One Contractor Router Plate
$39.99

Plate features an attachment that fits the standard T-Tracks on Contractor Clamps (sold separately) to firmly guide your router in a straight line along the clamp. The 6" diameter plate attaches easily to many popular routers for consistent and uniform performance.This Router plate is predrilled to fit the Porter Cable: 100, 690, 890 series, 8529Makita: 1100 series Hitachi: M12CV DeWalt: DW625, DW616, DW618 seriesBosch: 1617, 1618 series, 1619, 1619 EVS

Freud 97-276 3-Pc. Door Router Bit - 5/8" H x 1/2" Shank

Freud 97-276 3-Pc. Door Router Bit - 5/8" H x 1/2" Shank
$183.47

Set contains Premier Adjustable Ogee Rail and Stile Bits to mill tenons of any length! Simply remove the top portion of the cutter (including bearing and spindle) to produce the front of the long tenon profile for blind tenons, through tenons or bridle joints. These precise bits work for any door 5/8" to 1-1/4" thick. Unique cutter geometry virtually eliminates tearout. Adjustable shims enable a tight fit when using plywood and also allow use with panels as thin as 7/32". High-density carbide composition and Perma-Shield coating lengthen bit life and protect against heat and pitch build-up. 1/2" shanks. Also includes a 2-3/4" dia. Ogee Raised Panel Bit.

Rockler Drawer Pull Router Bit - 1-3/8" Dia x 7/8" H x 1/2" Shank

Rockler Drawer Pull Router Bit - 1-3/8" Dia x 7/8" H x 1/2" Shank
$49.99

Use this bit to apply a comfortable finger recess around the edges of doors and drawers, useful when you want a clean look without knobs or other hardware. You can also use it to rout finger pull stock that is applied separately, and you can even use it as a decorative edge treatment for table tops and other cabinet components.