Freud LU88R Industrial Thin Kerf Fine Finish Crosscut Saw Blades

This Perma-SHIELD coated blade gives new life to underpowered saws and produces smooth crosscuts in hardwoods, softwoods and moldings. Coated blades pull 1/3 less on the saw, which translates into 33% more cutting power. Thin kerf blades remove less material than standard carbide blades, thus requiring less horsepower to produce equally good results. The Perma-SHIELD coating covers the blade plate and cutting edge in a protective layer, reducing heat build-up. Perma-SHIELD blades resist binding in large volume cutting, reducing subsequent blade warp. The coating lubricates the blade, allowing it to spin freely, and eliminates pitch and debris build-up on the blade.

$49.47
Buy
 

Related Products

SD508 Freud Dado Set

SD508 Freud Dado Set
$199.97

The SD500 Series of dado sets cuts everything from veneered plywoods and laminates to solid wood, chip and splinter-free with a super smooth, flat bottom. The SD500 Series dado sets were the first to include a 3/32" thick chipper and has the flexibility of an adjustable dado to handle today's undersized plywood. This allows the cut width to be adjusted in 1/32" increments and doubles the number of slot widths available. A shim set is also included with the dado set for fine adjustments.Use on all table saws, and radial arm saws for cutting slots, grooves, dadoes, and rabbets in softwood or hardwood. SD506 is 6" in diameter, and SD508 is 8" in diameter. Both include (4) 1/8" , (1) 3/32" , and (1) 1/16" chippers.Technical Details:Cut chip-free dadoes, slots, grooves and rabbets3/32" chipper (included) for undersized plywoodShim set is included for fine adjustmentsCuts plywood & laminate to solid hard and soft woods3/32" chipper allows cut width to be adjusted in 1/32" incrementsCarbide tippedUse on table saws & radial arm saws5/8" arborSD506 Freud Dado Set (21697) is 6" in diameterSD508 Freud Dado Set (21697) is 8" in diameter

Kreg Rip-Cut Circular Saw Guide

Kreg Rip-Cut Circular Saw Guide
$34.99

There's no need to juggle guide rails, a pencil or tape measure. In fact, there's no measuring or marking required - just slide the fence on the Rip-Cut to any setting from 1/8" to 24" and rip a clean, straight line right down the length of the sheet. The Rip-Cut attaches easily to virtually any circular saw, whether left- or right-handed. Adjusting the fence is easy, simply open the cam lever, and slide it to your setting, just like a table saw fence.Quickly and easily connects to most hand-held circular saws.Reversible guide arm allows you to use it either right- or left-handed.Includes easy-to-read adjustable scale that can be zeroed to your blade.Fence moves with the saw, providing support through the entire length of the cut. Rips 4' x 8' plywood in two.

Rockler Sawhorse Clips for Bench Cookie Plus Pack of 4 Clips

Rockler Sawhorse Clips for Bench Cookie Plus Pack of 4 Clips
$10.99

Sawhorses are incredibly practical when you need a lightweight, portable work surface, but if you've used them much, you know that workpieces tend to rattle around and get scratched while you saw, rout and sand. With the Bench Cookie Plus Sawhorse Clips, that's no longer a problem. Simply slip the clips over your sawhorses, spin your Bench Cookies Plus on, and you have a no-mar, no-slip work surface that is easily resizeable for any workpiece. The grip is so secure, it's almost like having a fully equipped workbench with dog holes and a vise. Plus, you can slip some Bench Cookie Finishing Cones on for an ideal finishing surface with no worries about dripping stain on your nice workbench.