Products tagged with: turning

Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page

#1 Jaws for Oneway Scroll Chuck System

#1 Jaws for Oneway Scroll Chuck System
$52.49

Install these jaws on your Oneway Scroll Chuck (22719, sold separately) or Talon Chuck (20761, sold separately) for turning small bowls, knobs, vases or spindles.Chucking capacities of the Oneway Scroll Chuck with #1 Jaws:External (compression): 3/8" minimum, 2" maximumInternal (expansion): 7/8" minimum, 2-1/2" maximumChucking capacities of the Oneway Talon Chuck with #1 Jaws:External (compression): 3/8" minimum, 1-3/4" maximumInternal (expansion): 7/8" minimum, 2-3/8" maximum

#2 Replacement Bit for Oneway Termite, 1/2"

#2 Replacement Bit for Oneway Termite, 1/2"
$29.39

1/2" replacement ring bit for the Oneway Termite Hollowing Tool (32788, sold separately).

#3 Accessory Bit for Oneway Termite, 5/8"

#3 Accessory Bit for Oneway Termite, 5/8"
$30.49

This 5/8" accessory ring bit for the Oneway Termite Hollowing Tool (32788, sold separately) offers a broader cutting area for end-grain hollowing and finishing cuts on any flat or curved surface.

#3 Jaws for Oneway Scroll Chuck System

#3 Jaws for Oneway Scroll Chuck System
$58.79

These jaws fit the Oneway Scroll Chuck (22719, sold separately) and Talon Chuck (20761, sold separately) and have the mass and size necessary for turning larger bowls and vases. They are unparalleled in strength and holding capacity. The #3 jaws have also been outfitted with Oneway's patented profiled jaw design.Chucking capacities of the Oneway Scroll Chuck with #3 Jaws:External (compression): 3-3/8" minimum, 4-3/4" maximumInternal (expansion): 3-7/8" minimum, 5-3/8" maximumChucking capacities of the Oneway Talon Chuck with #3 Jaws:External (compression): 2-7/8" minimum, 4" maximumInternal (expansion): 3-3/8" minimum, 4-5/8" maximum

#3 Jaws for Oneway Stronghold Chuck

#3 Jaws for Oneway Stronghold Chuck
$57.79

The #3 Jaws for the beefy Oneway Stronghold Chuck (30589, sold separately) have the mass and size necessary for large bowls and vases. With their profiled jaws, they provide maximum gripping power with minimal damage to the piece.Chucking capacities of the Stronghold Chuck with #3 Jaws:External (compression): 3-7/8" minimum, 5-1/4" maximumInternal (expansion): 4-1/2" minimum, 6" maximumNote: If your lathe has less than a 16" swing, the Oneway Talon Chuck (20761) is recommended. Stronghold Chuck jaws are NOT compatible with either the original Oneway Chuck or the Talon Chuck.

1" X 8 TPI Insert for Oneway Scroll Chuck System

1" X 8 TPI Insert for Oneway Scroll Chuck System
$31.49

Allows you to mount a Oneway Scroll Chuck (22719, sold separately) or Talon Chuck (20761, sold separately) to a lathe with a 1" x 8 TPI drive spindle.

1'' Bushing for Rockler Lathe Tool Rest

1'' Bushing for Rockler Lathe Tool Rest
$14.99

If you want to enjoy the silky smooth finish of our Rockler Lathe Tool Rests, but you have a larger lathe with a 1'' I.D. holder, we've got you covered. This bushing slides over the 5/8'' post on any Rockler Lathe Tool Rest, making it compatible with 1'' holders. Use with the Rockler Lathe Tool Rest (e.g. 48674, sold separately)Made of black oxide coated steelIncludes two locking set screws

1-1/4" X 8 TPI Insert for Oneway Scroll Chuck System

1-1/4" X 8 TPI Insert for Oneway Scroll Chuck System
$31.49

Allows you to mount a Oneway Scroll Chuck (22719, sold separately) or Talon Chuck (20761, sold separately) to a lathe with a 1-1/4" x 8 TPI drive spindle.

10'' Contour Gauge

10'' Contour Gauge
$19.99

New 10" length contour gauge is ideal for measuring moldings for reproduction, duplicating spindles on the lathe, fitting flooring around moldings, copying curves and a variety of other contour matching jobs around the home and shop.Technical Details:10" long1/8" increments and mm increments embossed on gauge bodyBody is 1-3/4" wide x 10-1/2" longMetal reinforced plastic body 4 magnets on the side for easy storage

10'' Longworth Style Chuck

10'' Longworth Style Chuck
$139.99

Just rotate the plates of the Longworth Style Chuck and the soft silicone buttons close in almost instantly, and with perfect concentricity, to hold your project while you make the finishing cuts to the bottom side. Unlike many other rechucking methods, the silicone buttons won't mar your project or your finish. When compressed with the wing nuts, they expand to provide a secure grip. The 1/4" thick phenolic plates provide strength and stability, regardless of humidity. Available in two sizes: the 10" Longworth Style Chuck for mini and midi lathes with a 10" swing, and the 16" Longworth Style Chuck for standard-sized lathes with a 16" swing or larger. Pick up a piece of fine china, and the first thing you'll do after admiring the faceis turn it over to inspect the bottom and insignia. It's no different with turnedbowls, and turners work hard to make the bottom as beautiful as the top. Butchucking a finished bowl face down on the lathe without damaging it hasalways been a challenge - not with the Longworth Style Chuck. Simply rotatethe plates, tighten down the buttons, and you're ready to turn.Eliminates the time and inconvenience of installing, adjusting and readjustingordinary rechucking jaws.Capable of holding projects in compression or expansion mode (from theinside or outside of the rim of your turning project).Buttons close in concentrically, making it easy to center your project.Soft silicone buttons have increased length for better grip and expansioncapabilities.Buttons expand when the wing nut is tightened, and will not mark or deformyour turned piece.Includes 8 buttons. Replacement packs of buttons with hardware are availableseparately (47455).No assembly required.1/4" phenolic discs are extremely durable, stable, and spin in opposingdirections with almost no resistance.The back side of the Longworth Style Chuck has a steel disk approximately 3/8"thick for mounting.The disk is easily gripped by any brand of 4-jaw scroll chuck with the standard50mm #2 jaws.Straight jaws may be used, but dovetail jaws provide a better hold.The dovetail groove accommodates Nova chucks and Vicmarc chucks as well asOneWay type straight jaws.Recommended maximum RPM is 600.Intended for light finishing cuts only. Note for heavy stock removal. Note: Best practice for safety dictates that you engage the tailstock wheneverpossible. Remove the tailstock only when finishing the last bit in the very center,and for finish sanding.Specifications:Capacity in compression mode: 4-1/2" to 8" in diameter.Capacity in expansion mode: 5-3/4" to 9-1/2" in diameter.

16'' Longworth Style Chuck

16'' Longworth Style Chuck
$199.99

Just rotate the plates of the Longworth Style Chuck and the soft silicone buttons close in almost instantly, and with perfect concentricity, to hold your project while you make the finishing cuts to the bottom side. Unlike many other rechucking methods, the silicone buttons won't mar your project or your finish. When compressed with the wing nuts, they expand to provide a secure grip. The 1/4" thick phenolic plates provide strength and stability, regardless of humidity. Available in two sizes: the 10" Longworth Style Chuck for mini and midi lathes with a 10" swing, and the 16" Longworth Style Chuck for standard-sized lathes with a 16" swing or larger. Pick up a piece of fine china, and the first thing you'll do after admiring the faceis turn it over to inspect the bottom and insignia. It's no different with turnedbowls, and turners work hard to make the bottom as beautiful as the top. Butchucking a finished bowl face down on the lathe without damaging it hasalways been a challenge - not with the Longworth Style Chuck. Simply rotatethe plates, tighten down the buttons, and you're ready to turn.Eliminates the time and inconvenience of installing, adjusting and readjustingordinary rechucking jaws.Capable of holding projects in compression or expansion mode (from theinside or outside of the rim of your turning project).Buttons close in concentrically, making it easy to center your project.Soft silicone buttons have increased length for better grip and expansioncapabilities.Buttons expand when the wing nut is tightened, and will not mark or deformyour turned piece.Includes 8 buttons. Replacement packs of buttons with hardware are availableseparately (47455).No assembly required.1/4" phenolic discs are extremely durable, stable, and spin in opposingdirections with almost no resistance.The back side of the Longworth Style Chuck has a steel disk approximately 3/8"thick for mounting.The disk is easily gripped by any brand of 4-jaw scroll chuck with the standard50mm #2 jaws.Straight jaws may be used, but dovetail jaws provide a better hold.The dovetail groove accommodates Nova chucks and Vicmarc chucks as well asOneWay type straight jaws.Recommended maximum RPM is 600.Intended for light finishing cuts only. Note for heavy stock removal. Note: Best practice for safety dictates that you engage the tailstock wheneverpossible. Remove the tailstock only when finishing the last bit in the very center,and for finish sanding.Specifications:Capacity in compression mode: 4-1/2" to 14" in diameter.Capacity in expansion mode: 5-3/4" to 15-1/2" in diameter.

2-Piece Bushing Set for Whistle Key Ring

2-Piece Bushing Set for Whistle Key Ring
$4.99

A complete set of bushings for the Whistle Key Ring Hardware Kit (24573, sold separately). These bushings are precisely machined to match the diameters of your blank, allowing you to achieve smooth, perfectly flush seams. Simply turn your blank to match the bushing diameters, leaving a bit of extra material to allow for sanding.Technical Details:The Whistle Key Ring Bushing Set is made of nickel-plated mild steel-hard enough for excellent durability, yet soft enough to prevent damage to your turning tools.2-piece bushing set.Bushings are designed to work with the Whistle Key Ring Hardware Kit (24573, sold separately).Tip: when turning light-colored woods, apply a bit of CA glue to the bushings to prevent metal dust from migrating onto the turning blank.

3/4" x 16 TPI Insert

3/4" x 16 TPI Insert
$8.39

Necessary accessory for mounting the 4-Jaw Turning Chuck (26431, sold separately) to a lathe with a 3/4" x 16 tpi drive spindle.

3/4" X 16 TPI Insert for Oneway Scroll Chuck System

3/4" X 16 TPI Insert for Oneway Scroll Chuck System
$31.49

Allows you to mount a Oneway Scroll Chuck (22719, sold separately) or Talon Chuck (20761, sold separately) to a lathe with a 3/4" x 16 TPI drive spindle.

4-3/4" Face Plates

4-3/4" Face Plates
$29.99

This 4-3/4” diameter face plate mounts to a wide variety of lathe spindles by changing the threaded 1" x 8 TPI insert (#22432 Sold Separately). It is capable of being with Delta and Jet lathes just to mention a few and is idea for small to medium sized turning projects.The face plate is drilled with 3 countersunk screw holes to attach the insert form the back.

4-Jaw Turning Chuck

4-Jaw Turning Chuck
$106.99

Independently adjustable jaws allow you to lock in square or odd-shaped stock on your lathe. Stepped jaws can also be reversed for added versatility.Technical Details:Stepped jaws can also be reversed for added versatility.Internal measurements: 5-1/4" max., 3/8" min.6" dia. chuck includes key.1" x 8 TPI insert and 3/4" x 16 TPI insert sold separately.Independently adjustable jaws allow you to lock in square or odd-shaped stock. Stepped jaws can also be reversed for added versatility.

5/8" Alan Lacer Skew Chisel

5/8" Alan Lacer Skew Chisel
$79.99

Skew chisels designed by renowned turner and educator Alan Lacer are M2 High Speed Steel with ash handle.Available in two sizes: 5/8" and 1-3/8".Quality skew chisels made by Hamlet Craft Tools of England!Small skew chisel is 5/8" wide with 14" handle.Large skew chisel is 1-3/8" wide and has a 16" handle.Short point side is rolled completely for improve ease in planing spindle stock and for rolling beads.Long point side is kept flat, but with softened corners - an advantage in making such cuts as the V, shoulder, parting off, or pommels.For more information, see our Alan Lacer Skew Chisel Video

7mm Pen Barrel Cleaner

7mm Pen Barrel Cleaner
$13.99

The Barrel Cleaner clears glue residue from the barrel and also keeps the Barrel Trimmer at a 90° angle to the end of the pen, providing a flat, square mating surface and a tight fit for your hardware. Barrel Cleaner measure 3-3/4" long overall. Shank portion of each Pilot Shaft is 1-3/4" long x 3/16" in diameter.

Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page