Products tagged with: wood

Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page

#1 Jaws for Oneway Scroll Chuck System

#1 Jaws for Oneway Scroll Chuck System
$52.49

Install these jaws on your Oneway Scroll Chuck (22719, sold separately) or Talon Chuck (20761, sold separately) for turning small bowls, knobs, vases or spindles.Chucking capacities of the Oneway Scroll Chuck with #1 Jaws:External (compression): 3/8" minimum, 2" maximumInternal (expansion): 7/8" minimum, 2-1/2" maximumChucking capacities of the Oneway Talon Chuck with #1 Jaws:External (compression): 3/8" minimum, 1-3/4" maximumInternal (expansion): 7/8" minimum, 2-3/8" maximum

#2 Replacement Bit for Oneway Termite, 1/2"

#2 Replacement Bit for Oneway Termite, 1/2"
$29.39

1/2" replacement ring bit for the Oneway Termite Hollowing Tool (32788, sold separately).

#3 Accessory Bit for Oneway Termite, 5/8"

#3 Accessory Bit for Oneway Termite, 5/8"
$30.49

This 5/8" accessory ring bit for the Oneway Termite Hollowing Tool (32788, sold separately) offers a broader cutting area for end-grain hollowing and finishing cuts on any flat or curved surface.

#3 Jaws for Oneway Scroll Chuck System

#3 Jaws for Oneway Scroll Chuck System
$58.79

These jaws fit the Oneway Scroll Chuck (22719, sold separately) and Talon Chuck (20761, sold separately) and have the mass and size necessary for turning larger bowls and vases. They are unparalleled in strength and holding capacity. The #3 jaws have also been outfitted with Oneway's patented profiled jaw design.Chucking capacities of the Oneway Scroll Chuck with #3 Jaws:External (compression): 3-3/8" minimum, 4-3/4" maximumInternal (expansion): 3-7/8" minimum, 5-3/8" maximumChucking capacities of the Oneway Talon Chuck with #3 Jaws:External (compression): 2-7/8" minimum, 4" maximumInternal (expansion): 3-3/8" minimum, 4-5/8" maximum

#3 Jaws for Oneway Stronghold Chuck

#3 Jaws for Oneway Stronghold Chuck
$57.79

The #3 Jaws for the beefy Oneway Stronghold Chuck (30589, sold separately) have the mass and size necessary for large bowls and vases. With their profiled jaws, they provide maximum gripping power with minimal damage to the piece.Chucking capacities of the Stronghold Chuck with #3 Jaws:External (compression): 3-7/8" minimum, 5-1/4" maximumInternal (expansion): 4-1/2" minimum, 6" maximumNote: If your lathe has less than a 16" swing, the Oneway Talon Chuck (20761) is recommended. Stronghold Chuck jaws are NOT compatible with either the original Oneway Chuck or the Talon Chuck.

1" X 8 TPI Insert for Oneway Scroll Chuck System

1" X 8 TPI Insert for Oneway Scroll Chuck System
$31.49

Allows you to mount a Oneway Scroll Chuck (22719, sold separately) or Talon Chuck (20761, sold separately) to a lathe with a 1" x 8 TPI drive spindle.

1'' Bushing for Rockler Lathe Tool Rest

1'' Bushing for Rockler Lathe Tool Rest
$14.99

If you want to enjoy the silky smooth finish of our Rockler Lathe Tool Rests, but you have a larger lathe with a 1'' I.D. holder, we've got you covered. This bushing slides over the 5/8'' post on any Rockler Lathe Tool Rest, making it compatible with 1'' holders. Use with the Rockler Lathe Tool Rest (e.g. 48674, sold separately)Made of black oxide coated steelIncludes two locking set screws

1-1/2" x 1-1/2" Birch Embossed Carving

1-1/2" x 1-1/2" Birch Embossed Carving
$4.99

This quality carving comes ready to finish. Made of Birch. Measures 1-1/2" x 1-1/2" .

1-1/4" X 8 TPI Insert for Oneway Scroll Chuck System

1-1/4" X 8 TPI Insert for Oneway Scroll Chuck System
$31.49

Allows you to mount a Oneway Scroll Chuck (22719, sold separately) or Talon Chuck (20761, sold separately) to a lathe with a 1-1/4" x 8 TPI drive spindle.

1-3/4" Dentil Chair Rail

1-3/4" Dentil Chair Rail
$5.49

Protect your walls and add designer flair to your decoration with Dentil Chair Rail. Add a functional finishing touch to your dining room or other interior space. High-quality kiln-dried wood will color match to preserve a consistent and beautiful theme. 3/4" x 1-5/8" Dentil Chair Rail is available only in 6', 7' and 8' lengths.There is a $10 extra shipping charge per order.

1-3/4" Embossed Carvings-Select Option

1-3/4" Embossed Carvings-Select Option
$4.99

These quality carvings come ready to finish. Choose from Birch or Oak. Measures 1-3/4" in diameter.

1-3/4" H x 9-1/4" W Embossed Carvings-Select Option

1-3/4" H x 9-1/4" W Embossed Carvings-Select Option
$6.99

These quality carvings come ready to finish. Choose from Birch or Oak. Measures 1-3/4" High x 9-1/4" Wide.

1-3/4'' H by 5-1/4'' W Embossed Carvings

1-3/4'' H by 5-1/4'' W Embossed Carvings
$5.49

These quality birch carvings come ready to finish. Measures 1-3/4" High by 5-1/4" Wide.

10'' Contour Gauge

10'' Contour Gauge
$19.99

New 10" length contour gauge is ideal for measuring moldings for reproduction, duplicating spindles on the lathe, fitting flooring around moldings, copying curves and a variety of other contour matching jobs around the home and shop.Technical Details:10" long1/8" increments and mm increments embossed on gauge bodyBody is 1-3/4" wide x 10-1/2" longMetal reinforced plastic body 4 magnets on the side for easy storage

10'' Longworth Style Chuck

10'' Longworth Style Chuck
$139.99

Just rotate the plates of the Longworth Style Chuck and the soft silicone buttons close in almost instantly, and with perfect concentricity, to hold your project while you make the finishing cuts to the bottom side. Unlike many other rechucking methods, the silicone buttons won't mar your project or your finish. When compressed with the wing nuts, they expand to provide a secure grip. The 1/4" thick phenolic plates provide strength and stability, regardless of humidity. Available in two sizes: the 10" Longworth Style Chuck for mini and midi lathes with a 10" swing, and the 16" Longworth Style Chuck for standard-sized lathes with a 16" swing or larger. Pick up a piece of fine china, and the first thing you'll do after admiring the faceis turn it over to inspect the bottom and insignia. It's no different with turnedbowls, and turners work hard to make the bottom as beautiful as the top. Butchucking a finished bowl face down on the lathe without damaging it hasalways been a challenge - not with the Longworth Style Chuck. Simply rotatethe plates, tighten down the buttons, and you're ready to turn.Eliminates the time and inconvenience of installing, adjusting and readjustingordinary rechucking jaws.Capable of holding projects in compression or expansion mode (from theinside or outside of the rim of your turning project).Buttons close in concentrically, making it easy to center your project.Soft silicone buttons have increased length for better grip and expansioncapabilities.Buttons expand when the wing nut is tightened, and will not mark or deformyour turned piece.Includes 8 buttons. Replacement packs of buttons with hardware are availableseparately (47455).No assembly required.1/4" phenolic discs are extremely durable, stable, and spin in opposingdirections with almost no resistance.The back side of the Longworth Style Chuck has a steel disk approximately 3/8"thick for mounting.The disk is easily gripped by any brand of 4-jaw scroll chuck with the standard50mm #2 jaws.Straight jaws may be used, but dovetail jaws provide a better hold.The dovetail groove accommodates Nova chucks and Vicmarc chucks as well asOneWay type straight jaws.Recommended maximum RPM is 600.Intended for light finishing cuts only. Note for heavy stock removal. Note: Best practice for safety dictates that you engage the tailstock wheneverpossible. Remove the tailstock only when finishing the last bit in the very center,and for finish sanding.Specifications:Capacity in compression mode: 4-1/2" to 8" in diameter.Capacity in expansion mode: 5-3/4" to 9-1/2" in diameter.

13/32'' Thick by 7/8'' wide Embossed Molding

13/32'' Thick by 7/8'' wide Embossed Molding
$19.99

Use this hardwood embossed molding to add a decorative finished accent to furniture, cabinets, or shelves. Features a classic dentil molding pattern and can be stained or painted to suit your application. Easy to apply using brads and glue.Technical Details Sold in 48" lengths 7/8" wide X 13/32" thick Solid embossed hardwoodWhat's in the Box One 48" embossed molding.

16'' Longworth Style Chuck

16'' Longworth Style Chuck
$199.99

Just rotate the plates of the Longworth Style Chuck and the soft silicone buttons close in almost instantly, and with perfect concentricity, to hold your project while you make the finishing cuts to the bottom side. Unlike many other rechucking methods, the silicone buttons won't mar your project or your finish. When compressed with the wing nuts, they expand to provide a secure grip. The 1/4" thick phenolic plates provide strength and stability, regardless of humidity. Available in two sizes: the 10" Longworth Style Chuck for mini and midi lathes with a 10" swing, and the 16" Longworth Style Chuck for standard-sized lathes with a 16" swing or larger. Pick up a piece of fine china, and the first thing you'll do after admiring the faceis turn it over to inspect the bottom and insignia. It's no different with turnedbowls, and turners work hard to make the bottom as beautiful as the top. Butchucking a finished bowl face down on the lathe without damaging it hasalways been a challenge - not with the Longworth Style Chuck. Simply rotatethe plates, tighten down the buttons, and you're ready to turn.Eliminates the time and inconvenience of installing, adjusting and readjustingordinary rechucking jaws.Capable of holding projects in compression or expansion mode (from theinside or outside of the rim of your turning project).Buttons close in concentrically, making it easy to center your project.Soft silicone buttons have increased length for better grip and expansioncapabilities.Buttons expand when the wing nut is tightened, and will not mark or deformyour turned piece.Includes 8 buttons. Replacement packs of buttons with hardware are availableseparately (47455).No assembly required.1/4" phenolic discs are extremely durable, stable, and spin in opposingdirections with almost no resistance.The back side of the Longworth Style Chuck has a steel disk approximately 3/8"thick for mounting.The disk is easily gripped by any brand of 4-jaw scroll chuck with the standard50mm #2 jaws.Straight jaws may be used, but dovetail jaws provide a better hold.The dovetail groove accommodates Nova chucks and Vicmarc chucks as well asOneWay type straight jaws.Recommended maximum RPM is 600.Intended for light finishing cuts only. Note for heavy stock removal. Note: Best practice for safety dictates that you engage the tailstock wheneverpossible. Remove the tailstock only when finishing the last bit in the very center,and for finish sanding.Specifications:Capacity in compression mode: 4-1/2" to 14" in diameter.Capacity in expansion mode: 5-3/4" to 15-1/2" in diameter.

2-1/2" H x 10-5/8" W Embossed Carvings-Select Option

2-1/2" H x 10-5/8" W Embossed Carvings-Select Option
$8.99

These quality carvings come ready to finish. Choose from Birch or Oak. Measures 2-1/2" High x 10-5/8" Wide.

Pages: 1 2 3 4 5 6 7 8 9 10next pagelast page