Full Size Square Radius Carbide Replacement Cutter - Sr2

Take a close look at the edge of this carbide insert and you'll realize it's not actually square. Instead, each of its four edges is slightly crowned with a 2'' radius. This subtle change makes the cutter excellent for smoothing cuts. No sharpening required - just rotate to a new edge when the previous edge gets dull, and replace the cutter when needed. Features: Sr2 replacement cutter measures approximately 0.60'' square with a 2'' convex radius on all 4 edges. Solid carbide for a long life. Factory sharpened - ready for use right out of the box. Note: This cutter is not compatible with a standard square turning tool. Use it with the Full Size Square Radius Carbide Turning Tool only (48535, sold separately).

$19.99
Buy
 

Related Products

Newport Pen Bushing Set

Newport Pen Bushing Set
$4.99

A complete set of bushings for Newport Pen Hardware Kits (sold separately). These pen bushings are precisely machined to match the diameters of your pen blanks, allowing you to achieve the smooth, perfectly flush seams so valued in a top quality hand-turned pen. Simply turn your pen blanks to match the bushing diameters, leaving a bit of extra material to allow for sanding. Use with Newport Pen Hardware Kits; Gold, and Black Titanium .Technical Details:The Newport Pen Bushing Set is made of steel-hard enough for excellent durability, yet soft enough to prevent damage to your turning tools.3-piece bushing set.Bushings are designed to work with Newport Pen Hardware Kits (sold separately). Tip: when turning light-colored woods, apply a bit of CA glue to the bushings to prevent metal dust from migrating onto the turning blank.

Nova Pin Jaw Set

Nova Pin Jaw Set
$66.99

These special 25mm extended jaws are designed to act like a pin chuck, expanding into a pre-bored hole. This is an especially useful holding method for bowls with a free form edge. A big advantage over pin chucks is that you don't have to bore to an exact size - any size between the minimum and just under the maximum expansion will do. The longer jaw length allows for a very powerful spigot grip for smaller work like lace bobbins (up to 6" in length) and delicate pots. The jaws also have a dovetail for mounting small bowls (up to 6" in diameter). Capacity range when used with Nova Precision Midi chuck (47447, sold separately):Expansion mode: 1.024" to 1.378".Contraction mode (square stock): 0.276 " to 0.669".Contraction mode (spigot): 0.394" to 0.748".Capacity range when used with Nova G3 chuck (45748, sold separately):Expansion mode: 1.024" to 1.811".Contraction mode (square stock): 0.276 " to 1.102".Contraction mode (spigot): 0.394" to 1.220".Capacity range when used with Nova SuperNova 2 chuck (48906, sold separately):Expansion mode: 1.024" to 1.811".Contraction mode (square stock): 0.276 " to 1.102".Contraction mode (spigot): 0.394" to 1.220".Capacity range when used with Nova Titan chuck (45040, sold separately):Expansion mode: 1.024" to 2.244".Contraction mode (square stock): 0.276 " to 1.496".Contraction mode (spigot): 0.394" to 1.614".Features standard on all Nova Jaws:Nova chucks give you the same jaw fixing system and same insert/adapter system across all chuck models.All accessory jaws in the range will fit all the chucks in the range for optimum flexibility. Some, however, are not recommended. See individual jaws for recommendations.Nova chucks are specially designed so the jaws cut into the wood, grip firmly in the contraction mode and provide high tear out strength.

Blokkz Squid Center Finder

Blokkz Squid Center Finder
$19.99

Unlike most other center finders, the Blokkz "Squid" lets you quickly and easily find the center of square and rectangular stock in addition to the usual round stock. It also acts as a centering punch, as it features an integral sharpened awl, which slides up and down through the center to suit the size of your material. The four notched legs snugly straddle your material for accurate results, every time. Works with a range of diameters from less than 1/4" to a maximum of 2-3/8", and with on-edge material up to 1-5/8" thick. The punch rod is a sturdy 3/16" diameter stainless steel rod housed in a polycarbonate shell that can be easily disassembled should the need arise to sharpen the tip.Legs of the punch are notched to accurately center punch rectangular, round and square material.Ideal for pen turning and other spindle turning projects.Maximum width of round and square material is 2-3/8" by 2-3/8".Minimum material diameter is less than 1/4".Maximum thickness of on-edge material is 1-5/8".The Squid is easily disassembled in the event the punch needs to be sharpened.Made of high strength polycarbonate with a stainless steel punch rod.Hanger hole allows you to hang the Squid on a shop peg or nail.Assembly Required: Assemble Squid with bolts supplied. For best accuracy, tighten bolts until punch rod starts to bind and then back off slightly to allow the punch rod to slide freely.