Micro Mesh 3" X 6" 6000

Micro-Mesh is used to polish surfaces back to clarity or a high gloss. Available in grades 1500-12,000.Micro-Mesh (Grades 1500 through 12000) was originally designed to polish most hard plastics, fiberglass, epoxy, gel-coat, raw and finished wood, cultured marble, sold surface, painted surfaces, gold, silver, etc. Micro-Mesh is not an aggressive stock remover. Common sandpaper products are required for the removal of deep scratches prior to using Micro-Mesh to polish the surface back to clarity or a high gloss. Use wet or dry with either water or water/detergent as a lubricant. You may also use mineral oil, vegetable oil, lemon oil, etc but DO NOT use anything containing solvent as this will delaminate the MICRO-MESH. Sheets are offered in the following Micro-Mesh grades: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000, 12000

$4.49
Buy
 

Related Products

Nova Soft Jaw Set

Nova Soft Jaw Set
$21.49

Nova Soft Jaws consist of four segments of high-quality soft nylon, which can be cut and customized by the user to their specific requirements. Simply turn them with a scraper to the required dimensions. This allows woodturners to make a special set of non-marring jaws for unique projects. It also allows nearly full diameter contact with the workpiece, since you can turn out to the exact diameter required. Nylon can be turned to shape using standard tools. They can be turned, sawn, drilled or tapped.Because they are made of nylon, they hold most woods without marking. Vibrant red color makes it easy to see profiles. By machining the profile after mounting, you can eliminate any errors that may have added up from mounting the jaws to the chuck, then to the spindle.Maximum contact with workpiece. Near full diameter contact is achievable, since you can turn out to the exact diameter required.Thick jaw body lets user profile any shape they wish, limited only by the fastening heads, which are embedded 22.5mm from the face of the jaws.Outer ring diameter when closed: 120mm (4.7").Thickness: 27mm (1").Tips for customizing the soft jaws:It is recommended to use a scraper that is about 1/2" wide, with an end that is 90° to the side of the scraper. It will cut on both sides and on the end.Recommended bevel angle is about 70 degrees. When scraping nylon, the tool rest must be as close to the work as possible and you must always use a light touch. Run your lathe at a speed between 1700 and 2000 rpm for best cutting.You must take extra care when machining the jaws so as not to hit to hit the screw heads.Features standard on all Nova Jaws:Nova chucks give you the same jaw fixing system and same insert/adaptor system across all chuck models.All accessory jaws in the range will fit all the chucks in the range for optimum flexibility. Some, however, are not recommended. See individual jaws for recommendations. Nova chucks are specially designed so the jaws cut into the wood, grip firmly in the contraction mode and provide high tear out strength.

Manhattan Ballpoint Pen Hardware Kit - Black Titanium w/ Platinum

Manhattan Ballpoint Pen Hardware Kit - Black Titanium w/ Platinum
$13.99

With its elegant profile, superb balance, and smooth action, the Manhattan Pen has earned its place as a favorite among pen turners. It's a single twist pen - one turn of the barrel exposes the ballpoint tip. The Manhattan Ballpoint Pen takes standard Parker ballpoint pen refills. Choose from hundreds of eye-catching materials for the barrel. In hardly any time at all, you'll have a twist pen that will truly be turning heads. Turning Accessories Needed:Turning Blank (Sold Separately) Pen Turning Mandrel (Sold Separately) Manhattan Bushing Set (#43428 Sold Separately) 27/64" Drill Bit (#32111 Sold Separately)Also Available InGoldChromeChrome w/ Satin ChromeSatin Chrome w/ ChromeBlack Titanium w/ Titanium

Bushings for Sculpted Pen Kits

Bushings for Sculpted Pen Kits
$5.99

This is a complete set of bushings precisely machined to match the diameters of your pen hardware kit. The bushings let you easily gauge the progress of your turning, allowing you to achieve the smooth, perfectly flush seams so valued in a top-quality hand-turned writing instrument. Just turn the blank until the ends are almost flush with the bushings, then sand to final dimension. Made of steel-hard enough for excellent durability, yet soft enough to prevent damage to your turning toolsTip: when turning light-colored woods, apply a bit of CA glue to the bushings to prevent metal dust from migrating onto the turning blank