Box Joint Cauls

Make perfect joints with our Box Joint Jig and NEW Cauls!Uniformly spaced pressure points clamp individual box joint fingers at the corners to give you the tightest joints possible. Simply align the pressure points with box joint fingers and tighten in place with one or more Deluxe Ratcheting Band Clamps (41419, sold separately). Slots on the outside of the cauls are made to hold pennies firmly in place to support your Band Clamps at varying heights. Plastic cauls stand 6-1/4" (1/4" Cauls), 6-3/8"(3/8" Cauls) and 6-1/2" (1/2" Cauls) tall. Four Cauls per pack. Patent pending.

$10.99
Buy
 

Related Products

JIG IT Hinge Plate Template D

JIG IT Hinge Plate Template D
$7.99

Your doors will swing smoothly and line up neatly every time with our JIG IT templates to guide your way. Just butt the template up against the face of your cabinet and use a centering bit to drill perfectly positioned mounting holes for a wide variety of concealed hinges. See the compatibility info below for a list of which hinges are compatible with this template. Requires centering bit 68991 (sold separately). For even faster, more foolproof installation, use several of these templates mounted on one of our T-track rails (e.g. 26420, sold separately).For easier mounting of the cup plate from two-part Euro-style hinges, check out the JIG IT Deluxe Concealed Hinge Drilling System. It works with your handheld drill and sets up so you can bore precisely spaced hinge cup mounting holes on multiple doors.JIG IT Hinge Plate Template D Installs hinges: 33600, 36778, 49513, 47967,23261, 55926, 55933, 23554Use with #6 Self Centering Bit (68991, sold separately)These hinges are used on frameless cabinetsClear acrylic for easy alignment with your marksAlso includes T-track mounting hole for repeatable alignment and placement of hingesHole spacing and setback measurements are conveniently printed on the acrylic face for referenceStable, durable polymer fence

JIG IT Hinge Cup Drilling Jig, Bi-Fold

JIG IT Hinge Cup Drilling Jig, Bi-Fold
$9.99

Here's an accurate and inexpensive way to set up your drill press for boring the large diameter holes required for cup hinges. Simply align your fence with the hole in the jig, then tighten down your fence. You'll get consistently accurate holes with a perfectly set ''tab'' for your hinge. Set up couldn't be any easier! Made in USA. Appropriate ''tab'' (distance from door edge to edge of cup hole) is laser-etched onto the JIG-ITMade from stable, durable HDPE materialDrilling jigs available for 35mm and 26mm hinge cup holes

Non-Stick Pen Bushings for CA Finish

Non-Stick Pen Bushings for CA Finish
$6.99

Using CA glue to finish your pen turnings results in a lustrous, glossy polish,but it can also fuse your pen blank to the bushings. Not so with these non-stick polyethylene bushings in place, however. These bushings are made fromUHMW, the same super-slippery polymer used in our Plastic Jig Stock. They'repre-drilled for a standard mandrel, and have a 60° taper so they'll fit most anysize pen bushing. Just swap these for your metal bushings once the pen isturned, and apply your finish. 4-Pack.Technical Details:Non-Stick Pen Bushings are made of UHMW (Ultra-High Molecular Weight)polyethylene.Pre-drilled for a standard 7mm mandrel (e.g. 43537, sold separately).60° cone-shaped taper fits any size pen bushing.After shaping the pen blank, replace the metal bushings with non-stick plasticbushings and apply your CA finish.Self-lubricating UHMW has a low coefficient of friction, so it sheds glue easily.Very stable - 10x heavier than regular high-density polyethylene.High abrasion resistance and high impact strength even at low temperatures.Resistant to chemicals.