Grr-Ripper Micro Jig Replacement 1/4'' Leg

Every once in a blue moon you miss the tunnel of your Grr-Ripper push block and end up nicking the leg. Luckily, thanks to the push block, it's a lot cheaper to replace a plastic leg than a finger (and a lot less painful). All three Grr-Ripper replacement legs are available: the Center Leg, 1/4" Leg, and 1/2" Leg. All three are compatible with both the GR-100 and GR-200 Grr-Ripper models (sold separately, 62689 and 30737).Technical Details:1/4" leg is ideal for ripping thin stock.Installation hardware not included. Please use hardware from your previous Grr-Ripper leg.Keep the green Grr-Ripper pads clean with denatured alcohol or rubbing alcohol.

$14.99
Buy
 

Related Products

Rockler Pro Shelf Drilling Jig

Rockler Pro Shelf Drilling Jig
$84.99

Just lay the jig on your stock, tighten the two horizontal tracking knobs and start drilling error-free rows.Guarantees each row is perfectly in lineSpaces each hole exactly 37mm from the edge of your stockJig is easy to set up and easy to adjust for multiple rowsRows are spaced exactly 1-1/4" (32mm) apartPin holes are set back exactly 1-7/16" (37mm) from each edge32mm spacing and 37mm setback are fully compatible with the Euro hinge system24" long twin template tracks are joined by rigid rails that lock in place for error-free drillingDrill two rows with one jig to save time and ensure accuracyLocking 3-star tracking knobs allow for adjustments and ensure the jig stays firmly in placeReversible guide rails have a smooth aluminum surface on one side and a rubber fence on the other for better gripping powerIncludes two 5mm and two 1/4" indexing pins that eliminate the need for clamps and allow you to extend long rows of holes indefinitelyIncluded indexing pins store conveniently in the ends of each guide rail when not in useDrilling template is made of thick acrylic for durabilityDesigned for un-assembled cabinet components from 8-1/4"W to 25-1/4"W Self-Centering Drill Bits:Self-centering bits are pre-set to bore a consistent depth for perfect fitting shelf pins and sleeves every time. No adjustments are necessary! Various bit sizes available separately for both shelf pins and shelf pin sleeves. Decorative metal shelf pin sleeves provided added shelf strength.#40604 - 1/4'' Bit for 1/4'' Shelf Pin#40608 - 5mm Bit for 5mm Shelf Pin#41983 - 9/32'' Bit for 1/4'' Shelf Pin Sleeve#41981 - 7/32'' Bit for 5mm Shelf Pin Sleeve

Rockler Dust Collector for Rockler Dovetail Jigs

Rockler Dust Collector for Rockler Dovetail Jigs
$47.99

Finally, an affordable dust collection attachment for your Rockler dovetail jig! You don't have to spend hundreds of dollars to get dust collection with a dovetail jig. Our revolutionary new dust collector eliminates virtually all the dust created when cutting dovetails. It easily attaches to Rockler's dovetail jigs (both new and old!) and a shop vacuum or dust collection system to provide you with a clean cutting area and safe working conditions.Easily attaches to Rockler's dovetail jigs Built-in 2-1/4" port fits most shop vac hoses (not included).Sliding baffle directs the dust collection to where the dovetails are being cut.Sweep brush adjusts to provide a complete seal for stock thicknesses of 1/2" up to 1-1/8".Contains the dust while allowing the bit to travel through without damage.Two extra long 4" knob posts make adding your dust collector shroud easy.Built-in 2-1/4" port fits most shop vac hoses (not included).For older Rockler dovetail jigs with 4-screw side stops, conversion kit #25174 is required. (Sold out and no longer available).Patent pending.

1-1/4'' Movable Louver w/Front Control Arm Shutter Jig and Hardware

1-1/4'' Movable Louver w/Front Control Arm Shutter Jig and Hardware
$3.49

Whether you're a hobbyist or a professional woodworker, Rockler's 1-1/4'' Louver Shutter Template Set makes building your own Plantation-style Shutters easy and affordable. Build movable louver styles and save up to 75% over the cost of custom ordered shutters! It couldn't be easier with exclusive Rockler jigs, hardware, and pre-shaped louvers.Plus, with our online Shutter Design Wizard, you'll get a FREE Downloadable Plan for creating custom shutters, complete with detailed technical drawings, cross-section diagrams, elevations, and lists of all the supplies you need to complete your project! Before entering your dimensions into the design wizard, consult the Measuring Guide to determine your final shutter panel dimensions.Features:Easy, do-it-yourself jigs and templates for creating movable traditional-style shuttersSave up to 75% over the cost of custom ordered shuttersJigs make it a fool-proof process for drilling louver and control arm holesIncludes three self-centering bits for drilling shutter pin holes and control arm holesDrill bits have self-centering tips that fit perfectly into specific shutter template mounting holesA spring-loaded guide in the drill bits retract as pressure is applied and the drill bit advances