Leigh Super 18'' Dovetail Jig

Extraordinary joint making capability at an exceptional price point! Cut variably spaced Through & Half-blind dovetails easily and accurately.Infinitely adjustable one-piece fingers are easily positioned for any joint pattern, and you are always guaranteed a half pin at each edge of the joint.Rout half-blind pin boards and tail boards at the same time.The finger assembly can also produce two sizes of box joints, 5/16" and 5/8".Adjustments for fit can be made in increments of .002".You can even install the included crosscut fence and the dovetail finger assembly becomes a sliding dovetail template.Available in three widths: 12", 18" and 24" to satisfy the needs of every woodworker and every budget. The amazing joint making capability of Super Jigs is due in part to the revolutionary new Leigh E Bush (patent pending). A simple twist of the E Bush changes it's active diameter which in turn changes the fit of finger joints and half-blind dovetails.Standard Equipment:1/2" 8° dovetail bit1/2" 14° dovetail bit5/16" straight bit1/2" to 8mm collet reducerSliding dovetail fenceSquare drive screwdriverCam action speed clampsFully illustrated User GuideInstructional DVDSpacerLeigh E BushHalf-blind bridge piece materialOther features include:Easy to use cam action clampsAluminum clamp barsNon-slip material on every clamping surfaceInfinitely variable spacing

$399.00
Buy
 

Related Products

Micro Jig GRR-Ripper Attachment Kit GRAK-404

Micro Jig GRR-Ripper Attachment Kit GRAK-404
$20.99

For use with the Micro Jig GRR-Ripper Basic 3D Push Block System (GR-100) Sold Separately.Additional spacer and stabilizing accessory plate for extra control, ideal for narrow ripping.Attachment kit consists of additional spacer and stabilizing accessory plate for extra control ideal for narrow ripping.

Non-Stick Pen Bushings for CA Finish

Non-Stick Pen Bushings for CA Finish
$6.99

Using CA glue to finish your pen turnings results in a lustrous, glossy polish,but it can also fuse your pen blank to the bushings. Not so with these non-stick polyethylene bushings in place, however. These bushings are made fromUHMW, the same super-slippery polymer used in our Plastic Jig Stock. They'repre-drilled for a standard mandrel, and have a 60° taper so they'll fit most anysize pen bushing. Just swap these for your metal bushings once the pen isturned, and apply your finish. 4-Pack.Technical Details:Non-Stick Pen Bushings are made of UHMW (Ultra-High Molecular Weight)polyethylene.Pre-drilled for a standard 7mm mandrel (e.g. 43537, sold separately).60° cone-shaped taper fits any size pen bushing.After shaping the pen blank, replace the metal bushings with non-stick plasticbushings and apply your CA finish.Self-lubricating UHMW has a low coefficient of friction, so it sheds glue easily.Very stable - 10x heavier than regular high-density polyethylene.High abrasion resistance and high impact strength even at low temperatures.Resistant to chemicals.

Rockler Auto-Lock T-Track Clamp

Rockler Auto-Lock T-Track Clamp
$29.99

Tightening Rockler's new Auto-Lock T-Track Clamp is literally an open-and-shut case-just slide the clamp face up to your work and close the lever! Once set, the clamping pressure is always the same regardless of workpiece size, and is adjusted only if needed with the set screw. Since the clamps apply pressure from the side, the top of your workpiece is unobstructed for easy machining and sanding. The bottom-mounted pins slide inside the miter track for stability, and can be shifted for 45° angle clamping-ideal for miters and irregularly shaped objects. When used with our T-Track Table, the clamp arm can be adjusted in and out a full 3-1/2'', allowing you to easily clamp items that lie in between the T-tracks. Fast, repeatable action saves enormous amounts of time for repetitive clamping tasksClamps slide into any T-track that accepts 5/16'' T-bolts, including our T-Track Table (46654, sold separately) and many of the CNC Shark tablesAn optional Mounting Bracket (57940) is available for securing the clamp to shop-made jigs and fixturesKnurled wheel secures the clamp to your T-trackBottom-mounted alignment pins can be repositioned at 45° for angled clampingAdjustment screw is easily accessible through a hole in the handle, and adjusts clamping pressure from 10 to 500 lbsNon-slip pad on base of clamp prevents unwanted shiftingClamp face also features a pad that prevents marring your workpieceAngled notch in clamp face cradles outside corners and irregularly shaped objectsRugged steel and aluminum constructionNicely complements our T-Track Stops (e.g. 46010, sold separately)Fits all Rockler branded T-Tracks